Kenwood DPX 504 U, DPX304, DPX404U Item, Range, Display, Operation, Select “YES”, X’Over Setting, Operation type, Audio Preset Memory, 1Setup Sound Control, Select a preset number

Function of DPX504U

DSP Setup

X’Over Setting

Fine adjusting the following setting values corresponding to the X’Over values set in the section <Speaker Setting> (page 54).

Display		Item	Range
“X’Over”
	“Front”	“FC”	Front High Pass Filter
			Through, 30, 40, 50, 60, 70, 80, 90,
			100, 120, 150, 180, 220, 250 (Hz)
		“SLOPE”	Front High Pass Slope
			-6, -12, -18, -24 dB/Oct
	“Rear”	“FC”	Rear High Pass Filter
			Through, 30, 40, 50, 60, 70, 80, 90,
			100, 120, 150, 180, 220, 250 (Hz)
		“SLOPE”	Rear High Pass Slope
			-6, -12, -18, -24 dB/Oct
	“SubWoofer”	“FC”	Subwoofer Low Pass Filter
			30, 40, 50, 60, 70, 80, 90, 100, 120,
			150, 180, 220, 250, Through (Hz)
		“SLOPE”	Subwoofer Slope
			-6, -12, -18, -24 dB/Oct
		“PHASE”	Subwoofer Phase
			Reverse (180°)/ Normal (0°)
			(	: Factory setting)

1Select the source Press the [SRC] button.

Select a source other than “STDBY”.

2Enter Function setting mode Press the [VOL] knob.

3Enter X’Over setting mode

Turn the [VOL] knob and press it when the desired item is displayed.

Select “Audio Control” > “Detailed Setup” > “X’Over”.

4Select the speaker you want to set

Turn the [VOL] knob and press it when the desired item is displayed.

Select “Front”, “Rear”, or “SubWoofer”.5Select the item you want to set

Operation type	Operation
Selects the item.	Turn the [VOL] knob.
Adjust each item.	Press the [4] or [¢] button.
Set the value	Press the [VOL] knob.

6Repeat steps 4 to 5 to complete the X’Over settings.7Exit Function setting mode

Press the [   ] button for at least 1 second.

56DPX504U/ DPX404U/ DPX304

Audio Preset Memory

Registering the value setup by Sound Control.

1Setup Sound Control

Refer to the following operations to setup the Sound Control.

-<Car Type Selection> (page 54)

-<Speaker Setting> (page 54)

-<Car Type Fine Adjustments> (page 55)

-<X’Over Setting> (page 56)

-<Manual Equalizer Control> (page 49)

-<Listening Position Selection> (page 50)

-<Listening Position Fine Adjustments> (page 50)

2Enter Audio preset memory mode

Turn the [VOL] knob and press it when the desired item is displayed.

Select “Audio Control” > “Detailed Setup” > “Preset” > “Preset Memory”.

3Select the number to put in the memory Turn the [VOL] knob and press it when the desired item is displayed.

Select a preset number.4Turn the [VOL] knob and press it when the desired item is displayed.

Select “YES”.

“Memory Completed” is displayed.

5Exit Function setting mode

Press the [   ] button for at least 1 second.

⁄

•Register 6 patterns of Audio Preset Memory.

•Preset number “1”:

When you press the Reset, all the sources will be the setting value which is registered.

•Preset number “1” and “2”:

The memory cannot be erased by the Reset button.

•This function cannot be registered when the iPod Equalizer set in <Preset Equalizer curve Select> (page 49).