Appendix

Menu Glossary

•SRC Select

Setting up the Source Select mode.

1 : Displays source icons for your choice.

2 : Allows you to select sources one after another.

•BT DVC Status (Displaying the Bluetooth device Status)

You can display the connection status, signal strength, and battery level.

: Bluetooth cell-phone connection status.

: Bluetooth Audio connection status.

: Battery level of cell-phone.

Full Nearly dead : Signal strength of cell-phone.

Maximum Minimum

⁄

•Icons are not displayed if information cannot be obtained from the cell-phone.

•Since the number of steps of the control unit is different from that of the cell-phone, the statuses displayed on the control unit may discord from those displayed on the cell-phone.

•Auto Answer (Setting the Time Interval for Automatic Answer)

This function automatically answers (responds to) a call after lapse of the preset time interval for automatic answer.

“OFF” : Does not answer the phone call automatically.

“0” : Automatically answers the phone call at once.

“1s” – “99s” : Automatically answers the phone call after lapse of 1 – 99 seconds.

⁄

•If the time set in the cell-phone is shorter than that set in the unit, the former will be used.

•This function does not work for call waiting.

•SP Select (Setting up the Voice Output Speakers)

You can specify the voice output speakers.

“Front” : Outputs voice from the front-left and front- right speakers.

“F-R” : Outputs voice from the front-right speaker.

“F-L” : Outputs voice from the front-left speaker.

⁄

•Select the speaker which is further from the microphone in order to prevent howling or echoes.

•Call Beep (Setting the Beep of the Incoming Call)

You can output a beep from the speaker when a call comes in.

“ON” : Beep is heard.

“OFF” : Beep is canceled.

34 KDC-BT8041U/ KDC-BT8141U

•Display

If this unit is not operated at least 5 seconds with “OFF” selected, the display turns off. During a setup mode, the display will not turn off even if 5 seconds lapse.

•ILM Dimmer (illumination dimmer) Reduces the key Illumination brightness.

AUTO: Dims the illumination in conjunction with the Light switch of the vehicle.

MNAL1: Dims the illumination constantly.

MNAL2: Turns off the upper and lower illuminations, and dims the left and right illuminations.

OFF: Does not dim the illumination.

•SWPRE (Switching Preout)

Switches the preout between rear output (“Rear”) and subwoofer output (“Sub-W”).

•AMP

Selecting “OFF” turns off the built-in amplifier. Turning off the built-in amplifier improves the quality of the sound from Preout.

•Zone2 (Dual Zone)

Set the destination (front speaker “Front” or rear speaker “Rear”) of the sub source (AUX IN) when the Dual Zone function is turned on.

•Supreme

Technology to extrapolate and supplement with proprietary algorithm, the high-frequency range that is cut off when encoding at low bit rate (less than 128Kbps, Sampling frequency is 44.1kHz).

Supplementing is optimized by compression format (AAC, MP3 or WMA) and processed according to bit rate.

The effect is negligible with music that is encoded at high bit rate, variable bit rate or has minimal high frequency range.

•News (News Bulletin with Timeout Setting) Automatically receives news bulletin when it starts. Set the time during which interrupt is to be disabled after start of another news bulletin. Changing “News 00min” to “News 90min” turns this function ON.

If news bulletin starts when this function is ON, “NEWS” is displayed and news is received. If “20min” is has been set, reception of another news bulletin will not start for 20 minutes.

The news bulletin volume is the same level that was set for Traffic Information.

•Seek Mode (Tuning mode select) Select a tuning mode of the radio.

Tuning mode

 

Display

 

Operation

Auto seek

 

“Auto1”

 

Automatic search for a station.

Preset station seek

 

“Auto2”

 

Search in order of the stations in the

 

 

 

 

Preset memory.

Manual

 

“Manual”

 

Normal manual tuning control.