The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is using laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.
Marquage des produits utilisant un laser (Sauf pour certaines régions)CLASS 1
LASER PRODUCT
L’étiquette est attachée au chassis/boîtier de l’appareil et indique que l’appareil utiliser des rayons laser de classe 1. Cela signifie que l’appareil utilise des rayons laser d’une classe faible. Il n’y a pas de danger de radiation accidentelle hors de l’appareil.
La marca del producto láserCLASS 1
LASER PRODUCT
Esta etiqueta está colocada al chasis/a la caja e indica que el componente funciona con rayos láser de classe1.
Esto significa que el aparato utiliza rayos láser considerados como de clase débie. No existe el peligro de que este aparato emita al exterior una radiación peligrosa.
A marca dos produtos usando laser (exceto para algumas áreas)CLASS 1
LASER PRODUCT
A etiqueta é presa no chassis/estojo e indica que o componente utiliza raios laser, classificados como sendo de Classe 1. Isto significa que o aparelho está usando raios laser que são de uma classe mais fraca. Não há perigo de radiação maléfica fora do aparelho.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
KENWOOD CORPORATION
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR 1040. 10, CHAPTER I, SUBCHAPTER J.
Location : Rear PanelFCC WARNINGThis equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
NOTEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.NOTE
This Class B digital apparatus meets all requirements of the Canadian interference- Causing Equipment Regulations.
REMARQUECet appareil numérique de la classe B respecte toutes les exigences du Reglement sur le matériel brouilleur du Canada.
•Check that no metal objects (coins, tools, etc.) are left inside the unit to avoid short circuits.
•If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer.
2CAUTION
Take the following precautions to keep the unit in proper working order.•Do not open the top or bottom cover.•Do not install the unit in places it is exposed to direct sunlight, high heat or humidity, water may splash over it, or dust exists.
•Do not install the unit at a dusty place. If the unit is installed at a dusty place, dust accumulates inside the unit and unit may be damaged.
•When drilling a hole in the car to fix the brackets, make sure not to damage the fuel tank, brake tube, wiring harnesses, etc. on the other side.
•If the unit is installed near speakers, the speakers vibration may causes a sound skip. Install the unit as far away as possible from the speakers.
NOTE
•If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer.
•If it doesn't seem to be working properly, first press the Reset button. If the malfunction persists, consult your Kenwood dealer.
IMPORTANT INFORMATION•This unit is NOT designed to be connected directly to control units that are manufactured and sold before 1994. If used with such units, an optional
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT AND CONTROL UNIT.
•The disc name preset function can register names of up to 100 discs using up to 12 characters for each disc name.
The availability of this function as well as the number of discs which can be registered using this function and the number of usable characters may be variable depending on the control unit in use.
•Be sure to use round shape CDs only for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.
•Be sure to use CDs with disc mark
only for this unit.Cleaning the unit•If the front panel is dirty, wipe it clean with a silicon cloth or soft dry cloth with the power off.
2CAUTION
Do not use hard cloths or paint thinner, alcohol, or other volatile solvents. These may damage external surfaces or remove indicator characters.
Lens fogging•In cold climates, there may be a period after you turn on your vehicle's heater when the lens that guides the laser beam used in your CD player fogs up. If this happens, you cannot play compact discs. Take out discs and the fogging will disappear. If it does not return to normal after several hours, contact your Kenwood dealer.
Heat protection•In warm climates, when vehicles are left standing in direct sunlight with the windows closed, the temperature inside can rise above 60°C. The unit's protection circuits will then display the message "HOLD" and prevent the player from operating. Just open the windows or turn on the air conditioning. As soon as the "HOLD" message disappears, the player will operate normally.
2
3