Kenwood KIV-BT901 Item, Range, source, Display, X’Over Setting, 6Make a setting, Select the source, 1Select the source, Audio Preset Memory, 1Setup Sound Control

DSP Setup

X’Over Setting

Fine adjusting the following setting values corresponding to the X’Over values set in the section <Speaker Setting> (page 50).

Display		Item	Range
“X’Over”
	“Front”	“FC”	Front High Pass Filter
			Through, 30, 40, 50, 60, 70, 80, 90,
			100, 120, 150, 180, 220, 250 (Hz)
		“SLOPE”	Front High Pass Slope
			-6, -12, -18, -24 dB/Oct
	“Rear”	“FC”	Rear High Pass Filter
			Through, 30, 40, 50, 60, 70, 80, 90,
			100, 120, 150, 180, 220, 250 (Hz)
		“SLOPE”	Rear High Pass Slope
			-6, -12, -18, -24 dB/Oct
	“SubWoofer”	“FC”	Subwoofer Low Pass Filter
			30, 40, 50, 60, 70, 80, 90, 100, 120,
			150, 180, 220, 250, Through (Hz)
		“SLOPE”	Subwoofer Slope
			-6, -12, -18, -24 dB/Oct
		“PHASE”	Subwoofer Phase
			Reverse (180°)/ Normal (0°)

1Select the source

Press the [SRC] button repeatedly also switches

source.

Select a source other than “ STANDBY”.

✍❜SRC Select mode 2: Press the [SRC] button. Turn the [Volume] knob and press it when the desired item is displayed.

2Enter Audio Control mode Press the [Volume] knob.

3Enter X’Over setting mode

Turn the [Volume] knob and press it when the desired item is displayed.

Select “Detailed Setup” > “X’Over”.4Select the speaker you want to set

Turn the [Volume] knob and press it when the desired item is displayed.

Select “Front”, “Rear”, or “SubWoofer”.5Select the setting item to adjust

Turn the [Volume] knob and press it when the desired item is displayed.

6Make a setting

Turn the [Volume] knob to select a setting value, and then press the [Volume] knob.

7Repeat steps 3 to 5 to complete the X’Over settings

52KIV-BT901/ KIV-701

8Exit Audio Control mode

Press the [MENU] button for at least 1 second.

Audio Preset Memory

Registering the value setup by Sound Control.

1Setup Sound Control

Refer to the following operations to setup the Sound Control.

-Car Type Selection (page 50)

-Speaker Setting (page 50)

-Car Type Fine Adjustments (page 51)

-X’Over Setting (page 52)

-Manual Equalizer Control (page 47)

-Listening Position Selection (page 48)

-Listening Position Fine Adjustments (page 48)

2Enter Audio preset memory mode

Turn the [Volume] knob and press it when the desired item is displayed.

Select “Detailed Setup” > “Preset” > “Preset Memory”.

3Select the number to put in the memory Turn the [Volume] knob and press it when the desired item is displayed.

Select a preset number.

4Turn the [Volume] knob and press it when the desired item is displayed.

Select “YES”. “Completed” is displayed.

5Exit Audio Control mode

Press the [MENU] button for at least 1 second.

⁄

•Register 6 patterns of Audio Preset Memory.

•Preset number “1”:

When you press the Reset, all the sources will be the setting value which is registered.

•Preset number “1” and “2”:

The memory cannot be erased by the Reset button.

•This function cannot be registered when the iPod Equalizer set in <Preset Equalizer Curve Select> (page 47).