Kenwood TH-78A, TH78E 1 Paging Operation Overview

Paging uses a DTMF (Dual Tone Multi Frequency)

signal and is useful in calling members of a group, a

specific station, or for waiting for a call from another

station.

F: 145.020MHz

Individual Code: 111

F: 145.020MHz F: 145.020MHz F: 145.020MHz

lndividual Code 222 lndividual Code: 333 lndividual Code 444

Member 1 Member 2 Member 3

You should determine the common group paging

code and individual codes in advance. You can

enter three-digit codes from 000 to 999.

Unlike DTSS, the calling station code displays on the

transceiver so the receiving party can identify the

calling station. If called with an individual code, the

individual caller code displays. When called with a

group code, the group code displays.

1 Paging Operation Overview

1Set your station code.

Enter the paging mode. I

Call

Contents

Main ACCESSORIES .................... BEFORE OPERATION .............. .........................35 OPERATION AS A REPEATER CONTENTS SCANNING . . . . . . . 10 REPEATER OPERATION ...............34 CTCSS OPERATION THE DUAL TONE SQUELCH SYSTEM (DTSS) PAGING MESSAGE TRANSMISSION AND RECEPTION ENHANCED RECEIVER FUNCTIONS 4 ACCESSORIES BEFORE OPERATION CAUT/ON Page Page Page Page RECEIVER OPERATION 1 Getting Started 2 Tuning Control and Volume Control Page 3 Selecting a Frequency Page 4 Step Size Selection 5 Programmable VFO Tuning Limits 6 Basic Receiving Functions TRANSMITTER WARNING: 1717 1 To transmit, follow these steps: OPERATIONOPERATION 3 TX. Stop Function 4 Time-Out-Timer USING THE MEMORY 1 Microprocessor Memory Backup 19 2 Initializing The Memory 3 Memory Channel 4 Memory Contents 5 Entering Memory Data Entering Normal Simplex/Repeater Channels Clearing a Memory Channel 6 Entering Split Channel Frequencies 7 Entering The Call Channel Frequency 8 Recalling Memory Channels 9 Memory Shift 10 Memory Channel Character Display 23 SCANNING 1 Hold/Resume Programming Hold/Resume Selection 2 Scan operation cancel 3 Scan Options 4 Scanning Memory Channels 5 Band scan 6 Programmable Band Scan 26 Initiating Programmable Band Scan Confirming Scan Limit 7 MHz Scan 8 VFO/Memory Scan 9 CALL/VFO Scan 10 CALL / Memory Scan 11 V/M/C(VFO/Memory/CALL) Scan 12 The Alert Function REPEATER OPERATION 1 Transmitter Offsets 29 2 Selecting the Offset Direction 3 Automatic Offset Selection 4 Manual Offset Selection 5 The Reverse Function 30 6 Tone Operation 7 Autopatch Operations 32 8 DTMF Memory 33 OPERATION AS A REPEATER CTCSS OPERATION THE DUAL TONE SQUELCH SYSTEM (DTSS) 1 36 DTSS Code 2 Using the DTSS Function 1 Paging Operation Overview 2 Paging Code Memory 1~6 39 3 Setting Paging Codes Page Page 5 Receiving Pages (Wait) 6 Canceling Signal Squelch 7 Locking Out Codes 8 Answer-Back MESSAGE TRANSMISSION AND RECEPTION 1 Message Transmission Modes n 2 Using the Message Memory. Page 3 Message Memory Check 4 Message Memory Transmission 5 Message Reception n 6 Receive Message Memory n ENHANCED RECEIVER FUNCTIONS Alert 48 The Tone 1 2 Monitor 3 BeepOff 4 Lamp 5 Key Lock 6 Volume adjustment when you use an earphone 7 Switching speaker output when a speaker-microphone is connected 50 8 Automatic Band Change Function 9 Simultaneous Receive Function of Two Signal in the Same Band 10 Single Band Operation 11 52 MHz Mode 12 Channelized Frequency Display POWER SAVER FEATURES 1 The Battery Saver Mode 53 2 Automatic Power Off (APO) CLOCK FUNCTION 1 Time Setting 2 Timer Function Page DUPLEX OPERATION POWER ON MESSAGE AND FUNCTION MESSAGE 1 57 Power On Message 2 Function Message Page MAINTENANCE 1 General Information 2 Service 3 Record Keeping 59 TROUBLESHOOTING ACCESSORIES Page 1 Installing the CTCSS Unit (TSU-7) 63 2 Memory Expansion Unit (ME-l) 64 3 Programming the SMC-33 Remote Control Speaker Microphone 65 Memory Control Functions Press the key below. 66 Press the F key, then the key below. Press the key below. Page SPECIFICATIONS GENERAL RECEIVER TRANSMITTER QUICK REFERENCE TO DO THIS PRESS PRESS PRESS