KitchenAid W10271686C Installation Requirements, ToolsandParts, Location Requirements

INSTALLATION REQUIREMENTS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

■	Adjustable wrench	For LP/Natural Gas
■	Tape measure	Conversions
		■	T15 Torx®† screwdriver
	Marker or pencil
■		■	Adjustable wrench
	Pipe wrench
■		■	³⁄₈" drive ratchet
■ Flat-blade screwdriver
		■ ⁷⁄₈" socket
	¹⁵⁄₁₆" combination wrench
■		■ ½" deep-well socket
	Wrench or pliers
■		■ 7 mm nut driver

■Pipe-joint compound

resistant to LP gas ■ Masking tape

■Noncorrosive leak- detection solution

Parts Supplied

Check that all parts are included.

■Gas pressure regulator

■Burner grates

■Burner heads and caps

■Grill grate (on grill models)

■Wave tray (on grill models)

■Flame spreader (on grill models)

■Burner assembly (on grill models)

■Grease trays (2) (on grill models)

■Griddle drip tray (on griddle models)

■Grill drip tray (on grill models)

■Foam tape

■LP orifice package (W10221288)

■Conversion label (W10221320)

NOTE: The cooktop is manufactured for use with Natural gas. To convert to LP gas, see the “Gas Conversions” section.

Optional Backguards

48" (121.9 cm) models and grill models must be installed with a backsplash if installing at zero clearance to a combustible backwall. See “Cabinet Dimensions” in the “Location Requirements” section for installation requirements.

■36" (91.4 cm) Retractable Backguard Order Part Number 8284756

■48" (121.9 cm) Retractable Backguard Order Part Number 8284755

■9" (22.9 cm) Backguard for 36" (91.4 cm) Cooktops Order Part Number W10115776

■9" (22.9 cm) Backguard for 48" (121.9 cm) Cooktops Order Part Number W10115777

■22" (55.9 cm) Backguard with Shelf for 36" (91.4 cm) Cooktops - Order Part Number W10225949

■22" (55.9 cm) Backguard with Shelf for 48" (121.9 cm) Cooktops - Order Part Number W10225948

To order, see the “Assistance or Service” section of the Use and Care Guide.

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

High Altitude Conversion

To convert the cooktop for elevations above 6,560 ft (1999.5 m), order a High Altitude Conversion Kit.

■Part Number W10237848 - LP high altitude

■Part Number W10160841 - Natural gas high altitude

To order, see the “Assistance or Service” section of the Use and Care Guide.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner base.

■It is recommended that a 600 CFM or larger vent hood be installed above the cooktop.

■It is not recommended that a microwave hood combination be mounted above the cooktop.

■The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

■All openings in the wall or floor where cooktop is to be installed must be sealed.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■Grounded electrical supply is required. See “Electrical Requirements” section.

■Proper gas supply connection must be available. See “Gas Supply Requirements” section.

■The cooktop is designed to hang from the countertop by its side or rear flanges.

■The gas and electric supply should be located as shown in “Gas and Electric Connection Locations” section so that they are accessible without requiring removal of the cooktop.

■Provide cutout in left rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Mobile Home - Additional Installation Requirements

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

4