Manuals / Land Pride / Lawn and Garden / Brush Cutter

Land Pride RCP3060 Point Hook-up, Table of Contents, Assembly & Set-up, Refer to Figure, Category

Models: RCP2660 RCPM2660 RCPM3060 RCP3060

1 52

Download 52 pages 5.88 Kb

Page 16

3-Point Hook-up

Table of Contents

Section 1: Assembly & Set-up

Land Pride

3-Point Hook-up

IMPORTANT: Hydraulic fluid must be added to the cutter hydraulic reservoir before operating the pump. Otherwise hydraulic pump will be damaged.

Prepare cutter as follows:

1.Be sure transport safety chain is hooked to the deck. See Figure 1-15 on page 20.

2.Position cutter on a flat level concrete surface.

Refer to Figure 1-3:

3.There are three hitch categories represented in Figure 1-3. Determine which category fits the tractor being used and arrange cutter hitch pins as shown for that category.

Category III
Standard & Quick Hitch
Category II
Quick Hitch
Category II
Standard Hitch	24642

Hitch Pin Conﬁguration

Based on Hitch Category

Figure 1-3

Refer to Figure 1-4:

4.Slowly back tractor up to the Rotary Cutter while using tractor’s 3-point hydraulic controls to align lower hitch link holes with clevis holes on the cutter.

5.Place tractor gear selector in park and/or set brakes, shut engine off and remove ignition key.

6.Aligned and positioned tractor’s lower hitch holes in the clevises. Attach the lower arms to the clevises with hitch pins and secure with linch pins.

7.Adjust top center link in or out to align the center link hole with the cutter’s center hitch pin hole. Connect top center link to cutter hitch pin hole using customer supplied clevis pin and linch pin.

8.Make certain the lower 3-point arms are stabilized to prevent excessive side movement.

9.Return to tractor and slowly raise tractor 3-Point hitch about 1 to 2 inches. Stow jack stands in the raised position.

10.Slowly operate tractor's 3-Point arms up and down to check clearance between cutter components and tractor components. Move or remove tractor drawbar if it interferes with cutter.

11.Adjust tractor's lower arms to level cutter frame from left to right.

12.Adjust center top-link to level cutter frame from front to rear.

13.Final deck leveling adjustments will be made later.

23998

Tractor 3-Point Hitch

Figure 1-4

14 RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M

12/16/08

Image 16

Land Pride RCP3060 Point Hook-up, Table of Contents, Assembly & Set-up, Refer to Figure, Category, Standard & Quick Hitch

Contents

Table of Contents Parallel Arm Rotary CutterRCP2660, RCPM2660, RCP3060 and RCPM3060 316-111M Operator’s ManualTable of Contents Safety at All Times Look For The Safety Alert SymbolTable of Contents Important Safety InformationTable of Contents Important Safety InformationUse Safety Lights and Devices Use A Safety ChainTable of Contents Important Safety InformationPrepare for Emergencies Keep Riders Off MachinerySafety Labels 818-045C838-368C 818-142C818-229C 818-230C818-564C 818-230C818-555C 818-830CTable of Contents Important Safety Information818-339C 818-556C818-391C 818-390C818-554C 818-003C818-831C Table of Contents818-403C 818-484C818-388C 848-369CUsing This Manual ApplicationOwner Assistance IntroductionTable of Contents Land Pride Service Department 1525 East North StreetIntroduction Further AssistanceSection 1 Assembly & Set-up Tractor RequirementsTable of Contents RCP2660 & RCPM2660Dealer Preparations Table of ContentsSection 1 Assembly & Set-up Solenoid Controlled3-Point Hook-up Table of ContentsSection 1 Assembly & Set-up Refer to FigurePTO Hook-up Table of ContentsSection 1 Assembly & Set-up Check Driveline Minimum LengthFlow Control Valve Plumbing Fill Hydraulic ReservoirTable of Contents Section 1 Assembly & Set-upDANGER Hydraulic Hose Hook-upTable of Contents Section 1 Assembly & Set-upTable of Contents Section 1 Assembly & Set-upTractor Controlled Cylinders Breakaway CylinderSwitch Functions Electrical Hook-upTable of Contents Section 1 Assembly & Set-upOperational Checks Table of ContentsSection 1 Assembly & Set-up Float Switch Turned ONTable of Contents Section 1 Assembly & Set-upMomentary Push Button Switches Float Switch ControlTable of Contents Section 1 Assembly & Set-upPre-Operational Instructions Refer to Figure 1-15 & Figure 1-16 on pageTable of Contents Section 1 Assembly & Set-upPump & Motor Operation Refer to FigureGauge Wheel Model Set-up Table of ContentsSection 1 Assembly & Set-up Ratchet Jack InstallationHydraulic Flow Control Settings Section 2 AdjustmentsTable of Contents Refer to FigureDeck Level Adjustments Table of ContentsSection 2 Adjustments Refer to FigureSection 3 Operating Procedures Operating Check ListTransporting Table of ContentsCutting Operation Table of ContentsSection 3 Operating Procedures DANGERBreakaway Operating Procedures Un-hooking the Rotary CutterTable of Contents Section 3 Operating ProceduresTable of Contents General Operating InstructionsSection 3 Operating Procedures Hydraulic Control Options Operator Protective Shield OptionSection 4 Optional Equipment Table of ContentsHydraulic Plumbing Without Solenoid Hydraulic Plumbing With SolenoidSection 5 Hydraulic Plumbing Table of ContentsTable of Contents Section 5 Hydraulic PlumbingRefer to Figure Land PrideTable of Contents Section 5 Hydraulic PlumbingRefer to Figure Land PridePump & Motor Plumbing Table of ContentsSection 5 Hydraulic Plumbing Refer to FigureBreakaway Cylinder Plumbing Table of ContentsSection 5 Hydraulic Plumbing Refer to FigureMaintenance Section 6 Maintenance & LubricationCutter Blades Table of ContentsSkid Shoes Table of ContentsSection 6 Maintenance & Lubrication Refer to FigureTractor Maintenance Solenoid Valve BlockCutter Storage Table of ContentsLubrication Points HoursHours Table of ContentsTable of Contents Section 6 Maintenance & LubricationHours HoursMotor Spindle Hub Hydraulic ReservoirSpeed Increaser Table of ContentsSection 7 Speciﬁcations & Capacities Table of ContentsRCP2660 RCPM2660Table of Contents Section 7 Speciﬁcations & CapacitiesLand Pride 12/16/08Section 8 Features & Beneﬁts Table of ContentsFeatures BenefitsSection 9 Troubleshooting Table of ContentsProblem SolutionTable of Contents Section 9 TroubleshootingProblem SolutionTorque Values Chart Section 10 AppendixTable of Contents in-tpiWarranty Table of ContentsSection 10 Appendix Overall Unit and Driveline One year Parts and LaborCorporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA