Land Pride RCS3596 manual Operating Check List, Operating Checklist, Transporting, Offset Function

Land Pride Table of Contents

Section 3: Operating Instructions

Operating Check List

It is absolutely essential that no one operates the Rotary Cutter without first having read, fully understood and become totally familiar with the Operator’s Manual. Make sure the operator has paid particular attention to:

•Important Safety Information, pages 1 to 7

•Section 1: Assembly and Set-Up,page 9

•Section 2: Adjustments, page 14

•Section 3: Operating Instructions, page 15

•Section 4: Maintenance and Lubrication, page 18

In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training involved in the operation, transport, maintenance and storage of equipment. Before beginning to cut, the following inspection should be performed.

8.With the PTO disengaged and completely stopped, check cutting blades for sharpness.

9.(Lift-Type Cutter) Adjust tractor lower 3-point arms such that the PTO driveline is approximately level.

10.Set tractor throttle to idle or slightly above idle and slowly engage PTO. Initial start-up vibration is normal and should stop after a few revolutions. Stop PTO rotation if vibration continues. Wait for the PTO to come to a complete stop and then dismount from the tractor to check for probable causes.

11.Once the cutter is running smoothly, increase tractor PTO speed to the rated PTO speed. Stop PTO rotation immediately if vibration occurs and wait for PTO to come to a complete stop and then dismount from the tractor to check for probable causes.

IMPORTANT: Do not exceed rated PTO speed of the cutter. Excessive engine speed will cause damage to the power train components.

Operating Checklist

Check	Reference
“Important Safety Information” in	page 1 - 7
this Manual.
Be certain all guards and shields	Section 1
are in place.
Check oil level in gearboxes.	Section 4
	Page 21
Check that all plugs in gearbox	Section 4
have been replaced properly.	Page 21
Lubricate the cutter as needed.	Section 4
Refer to “Maintenance and	Page 21
Lubrication”.
Be sure nuts and bolts are tight.	Section 8

Make the following inspections after hooking-up to the cutter. See Tractor Hook-Upinstructions beginning on page 10. Make certain the PTO is disengaged and completely stopped before continuing.

4.Inspect tractor safety equipment to make sure it is in good working condition.

5.Carefully raise and lower the implement to ensure that the drawbar, tires, and other equipment on the tractor do not contact the frame or PTO driveline.

6.Check all hoses and wires to be sure that they will not contact PTO driveline. Check PTO guards to make certain they are in good condition and in place.

7.Inspect Hydraulic hoses for wear, damage and hydraulic leaks. See “Avoid High Pressure Fluids Hazard” on page 3. Replace damaged and worn hoses with genuine Land Pride parts.

Transporting

!CAUTION!

When traveling on public roads at night or during the day, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all federal, state and local laws

.

IMPORTANT: Always disengage the tractor’s PTO before raising the cutter to transport position.

1.When raising the cutter to the transport position be sure that driveline does not contact tractor or cutter.

2.Be sure to reduce tractor ground speed when turning; and leave enough clearance so the cutter does not contact obstacles such as buildings, trees or fences.

3.Limit transport speed to 20 mph. Transport only with a tractor of sufficient size and horsepower. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.

4.When traveling over rough or hilly terrain, shift tractor to a lower gear.

Offset Function

The main feature of your RCS35 Series Rotary Cutter is the hydraulic offset design. Being able to offset the cutter on the go increases your cutting efficiencies. Being able to maneuver the cutter versus steering around obstacles greatly increases your productivity. Easily operated by your tractor’s hydraulic lever, offsetting the cutter is at your fingertips. See “Hydraulic Hook-Up”on page 13.

6/26/06 RCS3596, RCSM3596, RCS3510 & RCSM3510 Series Rotary Cutters 312-708M 15