Manuals / Land Pride / Lawn and Garden / Brush Cutter

Land Pride RCSM3510 Lubrication, Hours, Tailwheel Spindle Tube, Tailwheel Hub, Gearbox & T-Box

Models: RCSM3510 RCSM3596 RCS3596 RCS3510

1 32

Download 32 pages 3.63 Kb

Page 23

Lubrication

Land Pride

Table of Contents

Section 4: Maintenance and Lubrication

Lubrication
Lubrication	Multi-purpose	Multi-purpose	Multi-purpose	50	Intervals in hours
Legend	spray lube	grease lube	oil lube		at which lubrication
Legend					is required

20701

20701

20701

24

Hours

Tailwheel Spindle Tube

Lift-Type Cutter

Type of Lubrication: Grease

Quantity = 6 pumps

8

Hours

Tailwheel Hub

The tailwheel hub is equipped with a relief hole located directly opposite the grease fitting. The relief hole releases pressure from inside the hub casting when it is greased. The hub should be greased until grease purges from the relief hole.

Type of Lubrication: Multi-purpose Grease

Quantity = Until grease purges from the relief hole

8

Hours

Gearbox & T-Box

Check oil level in the gearbox by removing the side plug in the gearbox case. If the oil level is low, remove the top plug in the gearbox case and fill with EP90 oil until oil flows from the side port of gearbox case. Reinstall plugs and tighten.

NOTE: Do not overfill! Cutter should be level when checking oil.

Type of Lubrication: EP90 Oil

Quantity = Fill until oil flows from the side port of gearbox case.

6/26/06

RCS3596, RCSM3596, RCS3510 & RCSM3510 Series Rotary Cutters 312-708M

21

Image 23

Land Pride RCSM3510, RCS3510 Lubrication, Hours, Tailwheel Spindle Tube, Tailwheel Hub, Gearbox & T-Box, Table of Contents

Contents

RCS3596, RCSM3596, RCS3510 & RCSM3510 Series Table of Contentsyou see this symbol, the subsequent Rotary CuttersSection 2 Adjustments Table of ContentsImportant Safety Information Section 1 Assembly and Set-UpBe Aware of Signal Words Safety at All TimesLook For The Safety Alert Symbol Important Safety InformationPractice Safe Mainte- nance Use Safety Lights and DevicesUse A Safety Chain Transport Machinery SafelyAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Keep Riders Off Machinery818-229C Safety Labels818-130C Shown 818-240C818-798C 818-543C818-552C 818-556C818-830C 818-564C818-142C 838-094C818-552C 818-540CTable of Contents Important Safety InformationIntroduction Using This ManualApplication Owner AssistanceWeight & Horsepower Pre-AssemblyChecklistTable of Contents Section 1 Assembly and Set-UpRefer to Refer to Figure Hitch AssemblyTailwheel Assembly Driveline InstallationFront Chain Guards Safety Guards OptionalDANGER Front Rubber GuardsRefer to Figure 1-9on page Vent Plug InstallationPTO Hook-up Tractor Hook-UpSection 1 Assembly and Set-Up Un-Hookingfrom the TractorHydraulic Hook-Up Table of ContentsMinimum Cutting Height Leveling ProcedureCutter Height Adjustment Section 2 AdjustmentsOffset Function Operating ChecklistOperating Check List TransportingRight Cutting InstructionsCrossing Steep Ditches & Banks Ditch / Bank Ditch / BankSection 3 Operating Instructions General Operating InstructionsTable of Contents Land Pride Cutter Blade Parts MaintenanceService Cutting Blades Section 4 Maintenance and LubricationTable of Contents Clutch Assembly and DisassemblyDriveline Clutch Clutch Run-InFlex Couplers Tractor MaintenanceSkid Shoe Maintenance Land Pride Skid Shoe Replacement PartsTailwheel Spindle Tube LubricationHours HoursTable of Contents Offset ArmsDriveline U-Joints DrivelineSection 4 Maintenance and Lubrication Flex CouplerRatchet Jack Table of ContentsTable of Contents Section 5 Speciﬁcations & CapacitiesRCSM3596 & RCSM3510 Series RCSM3596 & RCSM3510 Series Section 6 Features and BeneﬁtsTable of Contents FeaturesTable of Contents Section 7 TroubleshootingSolution Table of ContentsSection 7 Troubleshooting Problemft-lb3 N · m ft-lbN · m ft-lb Torque Values Chart for Common Bolt SizesSection 8 Appendix in-tpi1Section 8 Appendix WarrantyTable of Contents Corporate Ofﬁce P.O. Box