Manuals / Lathem / Computer Equipment / Time Clock

Lathem manual PC3500TX Terminal Installation & User’s Guide, Select the Advanced tab

Models: PC3500TX

1 33

Download 33 pages 49.22 Kb

Page 32

Image 32

28 - PC3500TX Terminal Installation & User’s Guide

Problem: Terminal does not accept New Day ( F2 key ) entries through the keypad.

Reason: The New Day function key ( F2 ) has not been enabled in the Terminal Manager software.

Solution: Open the PC3500TX’s Terminal Properties in Terminal Manager

•Select the Advanced tab

•Check the “Allow Start New Day Registration” box

•Click OK to save the changes

•Update the terminal with the changes

If you still have problems, please contact your authorized Lathem dealer.

Page 32

Image 32

Lathem manual PC3500TX Terminal Installation & User’s Guide, Select the Advanced tab

Contents

PC3500TX Terminal Installation & User’s GuideLimited One-Year Limited Warranty PayClock, Lathem and the Lathem logo are registered trademarks of Lathem Time Corporation. Other product names SETUP THE TERMINAL INSTALL/REPLACE THE OPTIONAL BACKUP BATTERYOPTIONAL SIGNAL DEVICE NETWORK WIRING TOPOLOGIESFeatures and Specifications WelcomeC H A P T E R PC3500TX NOTICE - For Firmware 177B and EarlierPower Surges and Spikes Note about Lithium BatteryPre-Terminal Installation Mounting the TerminalMount the Terminal C H A P T E RTo install the mounting bracket PC3500TX Terminal Installation & User’s Guide Turn the key clockwise to lock the terminal in placeConnect the Communication Cable C H A P T E RSetup the Terminal Starting the Test and Setup ModeSubnet Mask Network Test Not UsedPlug the terminal 12VDC power supply into the power connector To power up the terminal8 - PC3500TX Terminal Installation & User’s Guide Setup Mode - 177B Firmware For PayClock Pro 3.355G and earlier To Setup the PC3500TX’s Ethernet CommunicationsHIT ENTER IF DEFAULT ROUTE REQUIRED TERMINAL IP ADDRESS ###. ###. ###. ###HOST IP ADDRESS ###. ###. ###. ### NETWORK MASK ###. ###. ###. ###ENETADD=XXXXXXXXXXXX SETUP COMPLETE Setup Mode - 177G Firmware For PayClock Pro 4.1 and later Enet MAC Address XXXXXXXXXXXXTCP/IP Conn. Type To Setup the PC3500TX’s Ethernet CommunicationsTCP/IP Conn. Mode Default Router?Enter Socket Port # Enter Terminal IP ###. ###. ###. ###Enter Keepalive Mode Enter Sub Net Mask ###. ###. ###. ###Test Mode To start the Test ModeTEST MODE 128 YY “TEST MODE” PROG#Battery Test BATTERY TEST PASS ENTER TO RETESTNote If you do not have a battery installed, the test will fail SWITCH TEST SWITCH TO USE POSITIONRestart Mode Unlocking Your Terminal Through Terminal ManagerTo restart the terminal PRESS ENTER TO CLEAR ALL TRANSACTION DATAC H A P T E R Use the TerminalTo punch To transfer To start a New DayTo enter amounts To review your last punchWhen you see BADGE FOR SUPERVISOR OVERIDE, swipe your badge When you see ENTER ASSOCIATES BADGE, swipe the employee’s badgeSupervisor Functions To see employee InfoInstall/Replace the Optional Backup Battery A P P E N D I X AOptional Signal Device GENERAL SPECIFICATIONSTo connect your signaling devices A P P E N D I X BA P P E N D I X C Network Wiring TopologiesTypical Lan network configuration Typical Wan network configuration 24 - PC3500TX Terminal Installation & User’s GuideTroubleshooting the Terminal A P P E N D I X C26 - PC3500TX Terminal Installation & User’s Guide Problem The terminal is not communicating with the computerProblem A previously working terminal now is not operational Reason TEST/USE switch is not in the Use positionPC3500TX Terminal Installation & User’s Guide Problem The terminal does not accept badge dataReason Bar code badge is not manufactured to specifications Solution Refer to vendor’s manufacturing specifications28 - PC3500TX Terminal Installation & User’s Guide Solution Open the PC3500TX’s Terminal Properties in Terminal ManagerClick OK to save the changes Update the terminal with the changes Select the Advanced tabTerminal Data Sheet A P P E N D I X D