Manuals / Leica / Personal Care / Microscope & Magnifier

Leica dm750 p manual Time Delay Shutoff, Changing the status of the time delay shutoff

Models: dm750 p

1 45

Page 35

Time Delay Shutoff

The Leica DM 750 P is equipped with a time delay shutoff capability, which automatically turns the illumination off after 2

hours of no changes in the intensity control.

ϘϘ The time delay shutoff IS enabled as a default.

Changing the status of the time delay shutoff

1.Rotate the intensity control to the lowest setting.

2.Turn the power on.

3.Rotate the intensity control to full high intensity, then back to full low intensity all within 5 seconds.

ϘϘ The LED Illumination will flash to indicate the time delay shutoff status was changed.

ϘϘ The LED Illumination will flash two times slowly then stay on when you disable the Time Delay Shutoff.

ϘϘ The LED Illumination will flash three times quickly then stay on when you enable the Time Delay Shutoff.

When you turn the power off and then turn the power on again, the system will be in the last Time Delay Shutoff status (Enabled

or Disabled) and you will not see any blinking.

Leica DM750 P	Manual	35

Page 35

Image 35

Leica dm750 p manual Time Delay Shutoff, Changing the status of the time delay shutoff

Contents

Leica DM750 P Manual The Leica DM750 P Chapter overviewSafety regulations DimensionsContents Manual Safety regulationsLeica DM750 P Manual Safety conceptLeica DM750 P Important information Symbols used in this operating manualWarning of a danger Danger due to hot surfaceContact address Accessories from third-party suppliersImportant Notes DescriptionNon-intended use Instructions on useIntended use Place of useIntegration in third-party products Instructions on use continuedTransport DisposalDangers during use Health risks and dangers of useHealth risks Danger of infectionInformation for the person responsible for the instrument Information for the person responsible for the instrumentGeneral instructions Cleaning coated parts and plastic partsCleaning glass surfaces Care instructionsRepairs and service work Accessories, maintenance and repairAccessories MaintenanceElectrical data and ambient conditions Fuse ReplacementElectrical data EnvironmentManual The Leica DM750 PLeica DM750 P Manual IntroductionLeica DM750 P Manual UnpackingCheck the components against the planned configuration Leica DM750 PManual Get ReadyLeica DM750 P Tools used Attaching Analyzer Module or Analyzer/Bertrand Lens ModuleLeica DM750 P Viewing Tubeis seated with the orientation slot in the right eyetube 4. Insert the eyepieces into the eyetubesLeica DM750 P Installing ObjectivesAlways rotate the nosepiece by using the knurled nosepiece ring ration, please continue in this sectionSubstage Condenser Substage Condenser4. Completely loosen the two thumbscrews on the condenser mount Substage Condenser contManual Get SetLeica DM750 P Work Surface Basic setupPower Manual Using the Aperture Condenserobjective Leica DM750 Pmount. Swing it into place and be sure it clicks Setting up Polarized LightLeica DM750 P ManualManual Setting up Polarized Light contthe Analyzer into position Leica DM750 PFocusing Focusingin the slot of the right eyetube Viewing Tube AdjustmentAdjust the eyetubes for your interpupillary distance 1. Fold or unfold the eyetubes until you see one illuminated circleKoehler Set up Koehler Set up2. Focus the polarizing sample Objective CentrationTools used ϘϘ Centering keysManual Objective Centration contmodules Leica DM750 PLeica DM750 P Bertrand Lens Operationimage through the eyepieces You can now view the conoscopic image through the eyepiecesChanging the status of the time delay shutoff Time Delay ShutoffManual Leica DM750 PManual Ready! Set! GoLeica DM750 P Manual Care of the MicroscopeLeica DM750 P Manual General maintenanceGeneral Leica DM750 PGeneral maintenance cont Manual Mechanical MaintenanceMechanical Maintenance Leica DM750 PManual DimensionsLeica DM750 P Manual Leica DM750 PManual Leica DM750 PManual Leica DM750 P