Lennox Hearth PS40 Features and Specifications

Features and Specifications		CAUTION: THE USE OF UNAPPROVED, DIRTY, WET
		AND/OR HIGH SALT CONTENT FUEL WILL VOID THE
Installation Options		WARRANTY!
•	Residential	Wood pellets manufactured to the pellet fuels institute (P.F.I.)
•	Vented vertical and horizontal (see venting instruc-
		certification standard are available in two grades, Standard
	tions)
		and Premium. The primary difference between the two is
• Manufactured home and mobile home
		the ash content of the pellets.
•	Thermostat or manual operation
•	Bedrooms	The P.F.I. specification for standard grade & premium grade
		residential pellet fuel is as follows:
Heating		• CHLORIDES (Salt): Less than 300 p.p.m. to avoid stove
• Max. feed rate is 4.7 pounds/hour or 39,500 BTU/hour		and vent rusting.
• Min. feed rate is 1.8 pounds/hour or 15,120 BTU/hour		• BULK DENSITY: 40 lb. / Cu. Ft. minimum
Venting		• MOISTURE CONTENT: 8% maximum
		• ASH CONTENT: < 3% maximum (standard grade) < 1%
This stove is approved for venting with Type L and Type		maximum (premium grade)
PL pellet vent pipe. The flue collar on the stove accepts		• FINES: 0.5% maximum through a 1/8” screen
3”diameter pipe.		• BTU CONTENT: There are a number of variations in pellet
The combustion air for this stove is drawn through a pipe		fuels that are not included in PFI standards. For example,
		BTU (heat value) content may range from just under 8,000
at the lower rear of the stove. For mobile home installations		to almost 9,000 Btu, depending upon species and region
a 3” ID flex line or pipe must be attached to the stove’s air		of the country and other variables.
intake to draw air from outside the house. The vent pipe can		Corn Specifications: Use only clean-shelled corn with a
be installed vertically or horizontally (see Venting section		moisture content less than 15% and approximate fuel value
for recommended installations).		of 7000 BTU/lb (16,200 kJ/kg). Do not attempt to burn corn
		with higher moisture content or burn lesser grade fuels. Do
Electrical		not burn other types of agricultural pellets or byproducts
• The stove requires 120 volts AC for operation.		(alfalfa, cherry pits, olive pits, nut shells, etc.) as they are
•	Maximum wattage is 700.	not permitted to be burned in these appliances.
• Igniter wattage is 400.		Weight - 265 pounds
• Normal operating wattage is 300.
Thermostat		Hopper Capacity - 60 pounds
This stove can be operated manually or with a thermostat.		Listing information
Lighting		The Winslow™ PS40 stove is safety tested and listed with
This stove is equipped with an electric self igniter for ease		the following agencies;
of ignition.		• OMNI-TestLaboratories,Inc.,Beaverton,OregontoASTME
		1509
Fuel Specifications		• USEPA List of Exempt Wood Heating Appliances
This stove is designed to burn wood pellet fuel. In addition,		• List of Colorado Approved Pellet Stoves
a corn/wood pellet mixture, with a maximum of 50 percent
corn can be burned. Burning any other fuel that is not ap-		Appearance Choices
proved for use with this appliance will void the appliance
		The Winslow PS40 stove can be ordered with the following
warranty. IMPORTANT: The corn/wood mix needs to be
		door trims and grills, log set, and brick panel options:
mixed evenly before being put in the Winslow™ pellet
stove hopper.		Door Trim Kits		Grill Kits
Wood Pellet Specifications: This appliance has been		Black	79038	Black	79000
		Gold	79034	Gold	79001
designed to burn wood residue pellets with up to 3% ash
		Nickel	79037	Nickel	79002
content. Dirty fuel will adversely affect the performance of the
		Brushed Nickel	79035	Brushed Nickel	79022
stove. Any questions regarding pellet fuel can be answered
		Black Nickel	79036	Black Nickel	79039
at the Pellet Fuels Institute (PFI), www.pelletheat.org.
		Log Set - Required		H5142
		Brick Panel Kit -Required		79030
	NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.