Reference: Detailed Information For Making A Master TV
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know how to enter the TV Installer menu and make changes to
the default values as required. If necessary, famil- iarize yourself with the TV Installer menu and how to make and save changes in the menu, before attempting to
clone the TV Master TV setup.
You will also need an LG Installer remote control similar to the one shown in the front of this manual. The installer remote must have a “Source” button or its equivalent. The remote shown in this manual has a “INPUT” button
Finally, the TV’s clonable features need to be set up. This is a critical step. If the Master TV display panel’s clonable features
like adding channel icons or channel labels, digital font options etc., are not correctly added, then the cloned TVs will all have problems.
As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel.
Making a Master TV
Detailed Instructions
The following describes the procedure for preparing a Master TV for cloning and the procedure for adding Channel Icons and/or Labels.
Note 1: Disconnect all Aux inputs. Under certain conditions, EZ Channel Scan is disabled if there is an Aux input active.
Note 2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu.
1.Enter the TV installer menu.
a.Reset the internal controller to factory default by access- ing installer menu item 117 FACT DEFAULT, set it to 1 and press “ENTER”. The value will change back to 0 after the TV’s internal controller has been restored to factory default con- dition. This step will ensure that the TV channel memory will be the active channel list. Check the Status LED. If it is blinking rapidly then the TV channel map is in use.
b.Within the Installer menu, set the Installer menu items to the configuration required of your institution.
c.It is important to set the tuning band at this time, see Installer menu item 03 BAND/AFC.
d.Set Installer menu item 28 – CH OVERIDE to 001 to allow access to the EZ Channel Scan and Surf List/Ch. Edit features in the SETUP Menu. Exit the Installer menu.
2.Access the Master TV menus and set the clonable options on the menus to the desired configuration. Refer to the Clonable Menu Features Chart on page 16 in this manual.
3.Run EZ Channel Scan to find analog and digital channels.
4.Enter the Channel Edit menu and edit the channel lineup to include the
5.Assign ICONs to the channels using the Channel Label Menu. Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS or labels for channels without Icons.
6.Transfer the TV setup: Enter the TV installer menu. Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the TV. Once the transfer is complete, the system will exit the Installer menu. Check the Status LED inside the TV. It should be blinking slowly (1 blink per second).
7.Edit/Add Channel ICONs and Channel Labels as needed.
Enter Installer menu. With menu displayed, press
-Editing/Adding Channel ICON and Labels on Master TV
-Changing a Channel’s ICON on Master TV
-Changing/Adding Channel Labels on Master TV
-Changing Source Labels on Master TV
8.Verify Master TV setup and feature configuration:
•Did you add Channel ICONS?
•Did you add Channel Labels?
•Did you add Source Labels?
•Did you adjust all TV menu options as required?
After verifying master setup, enter the TV Installer menu and set Installer menu item 28 CH OVERIDE to 000. Press ENTER to remove and exit the Installer menu.
P A G E 1 8 |
