LG Electronics 60PA6500, 60PA5500 English, External Control Device Setup, OSD Select Command k l

				EXTERNAL CONTROL DEVICE SETUP 99
12. OSD Select (Command: k l)			18. ISM Method (Command: j p)
To select OSD (On Screen Display) on/off.				To avoid having a fixed image remain on screen.
	Transmission [k][l][ ][Set ID][ ][Data][Cr]		Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data 00: OSD off		Data 01: OSD on		Data 02: Orbiter
				08: Normal
	Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
				20: Color Wash
13. Remote Control Lock Mode (Command: k m)				Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
To lock the remote control and the front panel
controls on the set.			19. Energy Saving (Command: j q)
				To control the energy saving function.
	Transmission [k][m][ ][Set ID][ ][Data][Cr]

Data 00: Lock off Data 01: Lock on

Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]

If you’re not using the remote control and front panel controls on the Monitor set, use this mode. When main power is on/off, remote control lock is released. If Key Lock is on in the standby mode, TV will not turn on by POWER button of remote control and on the TV.

14.Treble (Command: k r) To adjust treble.

You can also adjust treble in the AUDIO menu.

Transmission [k][r][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to “Real data mapping”. Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]

15.Bass (Command: k s) To adjust bass.

You can also adjust bass in the AUDIO menu.

Transmission [k][s][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to “Real data mapping”. Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]

16.Balance (Command: k t) To adjust balance.

You can also adjust balance in the AUDIO menu.

Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to “Real data mapping”. Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]

17.Color Temperature (Command: x u) To adjust color temperature.

You can also adjust color temperature in the PICTURE menu.

Transmission [x][u][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to “Real data mapping”. Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

Transmission [ j ][q][ ][Set ID][ ][Data][Cr]

Data 00: off

01:Minimum

02:Medium

03:Maximum

04:Auto/Intelligent sensor (depending on model)

05:Screen off

Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]

20.Auto Configuration (Command: j u)

To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode.

Transmission [ j ][u][ ][Set ID][ ][Data][Cr] Data 01: To set

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

21.Channel Tuning (Command: m a)

To tune channel to following physical/major/minor number.

Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel to the Major number, the Physical number is not required when sending a command.

Data 00: Physical Channel Number

NTSC air: 02~45, NTSC cable: 01, 0E~7D

ATSC air: 01~45, ATSC cable: 01~87

Data 01 & 02: Major Channel Number

Data 01: High byte Data 02: Low byte

Two bytes are available for the Major and Minor, normally only the second byte is used.

Data 03 & 04: Minor Channel Number Not needed for NTSC.

The table above lists the binary code which must be converted to Hexadecimal before sending. For example:

The binary code to tune the sub source to an NTSC cable channel is “1000 0001”, which translates to “81” in Hex.

*7th bit : For which source do you want to change the channel.

*6th bit: Use a two part or one part channel. Most

ENGLISH