Manuals / LG Electronics / Laundry Appliance / Washer

LG Electronics WD(M)-10220(5)FD XAMmax, Sound, Replace the STATOR ASSEMBLY or ROTOR ASSEMBLY

Models: 16221FD 10220(5)FDB(N)

1 36

Download 36 pages 20.86 Kb

Page 22

Image 22

Is the softener cap clogged?

Is water supplied?

Option(Hot)Wiringdiagram

XAMmax

SOFTENERYESDOES NOT FLOW IN

Are receptacles correctly connected to the terminals		NO
of the INLET VALVE ASSEMBLY?YES
drawer?	YES	YESNO
Is softener put in the correct compartment of the

Refer to

NO WATER SUPPLY

Check the wiring on the dispenser.

Put it in the correct compartment.

Clean the cap and drawer.

ABNORMALNO	SOUND	YES
Is the motor bolt loosened?		YES
Is there friction noise from the motor?		YES

Fix the bolt tightly.

Replace the STATOR ASSEMBLY or ROTOR ASSEMBLY.

Page 22

Image 22

LG Electronics WD(M)-10220(5)FD XAMmax, Sound, Are receptacles correctly connected to the terminals, Yes No, Abnormalno

Contents

e-mail http//LGEservice.com/techsup.html SERVICE MANUALWASHING MACHINE AUG. 2003 PRINTED IN KOREA P/No.3828ER3018UCONTENTS 1. SPECIFICATION Jumbo drum 2. FEATURES & TECHNICAL EXPLANATION2-1.FEATURES More economical by Intelligent Wash System2-4.THE DOOR CAN NOT BE OPENED 2-2.DETERMINE WASHING TIME BY FUZZY LOGIC2-3.WATER LEVEL CONTROL water temperature3. PARTS IDENTIFICATION ACCESSORIESLowerAdjustablecoverfeetcap DrainDoorplugpumpfilter128004. INSTALLATION Check that the rubber washer is inside of the valve connector HOW TO CONNECT INLET HOSECONNECT POWER PLUG Connect the power plug to the wall outletTEST OPERATION Wash program selector 5. OPERATIONWater temperature selector LED displayChild - Lock Time DelayPower button Spin button6. WIRING DIAGRAM / PROGRAM CHART MAIN PWBDD7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY 7. TROUBLESHOOTING7-1.BEFORE PERFORMING SERVICE 7-2.QC TEST MODESYMPTOM 7-4.ERROR DISPLAYCAUSE MAIN PWB ASSEMBLY is out of order ERROR SYMPTOMCAUSE SYMPTOM 8. ERROR DIAGNOSIS AND CHECK LIST8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION GUIDE FOR SERVICE CALLCheck if the door switch is O.K SYMPTOMGUIDE FOR SERVICE CALL Close the doorClean the compartment for softener SYMPTOMGUIDE FOR SERVICE CALL LOW-SUDSINGNO POWER 8-2.FAULT DIAGNOSIS AND TROUBLESHOOTINGNONO DETERGENT DOES NOT FLOW IN XAMmaxNO WATER SUPPLY PRE+MAIN MAIN WASHReplace the STATOR ASSEMBLY or ROTOR ASSEMBLY XAMmaxSOUND of the INLET VALVE ASSEMBLY? YESRemove foreign material Reconnect or repair the connector MAINPWBASSEMBLY12Replace the S.PRESSURE SWITCH ASSEMBLY Replace the MAIN PWB ASSEMBLY Repair the DRAIN HOSE ASSEMBLYHose ConnectorGray NormalReplacethe HEATERASSEMBLYbetween 10~30the same time after power off, press the Start/Pause SPIN TROUBLEWhen pressing Opt.2, Spin and POWER buttons at Replace the MAIN PWB ASSEMBLYHook CONTROL PANEL ASSEMBLY9. DISASSEMBLY INSTRUCTIONS PUSH DISPENSER ASSEMBLYDISPENSER ASSEMBLY OptionLOWER COVER INLET VALVE ASSEMBLY3Option2DOOR ASSEMBLY GASKETDamper Clean the drain pump filterHinge HEATER ASSEMBLY DRAIN PUMP ASSEMBLYTHERMISTOR Take apart the CLAMP ASSEMBLY cabinet and release the GASKET SWITCH ASSEMBLY, DOOR LOCKWHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB Unscrew 2 screws holding the DOOR SWITCH ASSEMBLYA140 10. EXPLODED VIEW AND PART LISTA103 10-1.THE A153PART LIST OF CABINET ASSEMBLYF436 F431 F441 10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSEMBLYF324 F321 F300 F320 F225 F220 F430K540 10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLYK346 K344

XAMmax

Are receptacles correctly connected to the terminals

YESNO

Put it in the correct compartment.

SOUND

Is the motor bolt loosened?

Is there friction noise from the motor?

Replace the STATOR ASSEMBLY or ROTOR ASSEMBLY.