Manuals / LG Electronics / Laundry Appliance / Washer

LG Electronics WD(M)-14220(5)FD, 16221FD XAMmax, No Water Supply, Detergent Does Not Flow In

Models: 16221FD 10220(5)FDB(N)

1 36

Download 36 pages 20.86 Kb

Page 21

NO WATER SUPPLY

NO WATER SUPPLY

Option(Hot)

Option(Hot)Wiringdiagram

XAMmax

Is water supply shut-off?YESNO			YESNO
Is the tap opened?
When you press both Rinse button and Spin button
simultaneously, is the water level frequency below
240?	NO		YES
Is the inlet valve filter cloggedNOwith impurity?
Is resistance between each terminal of INLET			NO
VALVE ASSEMBLY is 2~8YESk		?
Check the voltage of the inlet valve connector			NO
220 - 240V~.
(Refer to 7-2 QC TEST MODE)
DETERGENT DOES NOT FLOW IN
Is water supplied?	YES		NO
Are replaceptacles correctly connected to the			NO
terminals of the INLET VALVEYES		ASSEMBLY?
Is detergent put in the correct compartment of			NO
the drawer?	YES
Is the detergent caked or hardened?			YES

Open the tap.

Check the AIR CHAMBER and the tube clogged with impurity.

Clean the filter.

Replace the INLET VALVE

ASSEMBLY.

Replace the MAIN PWB

ASSEMBLY

Refer to

NO WATER SUPPLY

Check the wiring on the dispenser.

Put the detergent in the correct position

PRE+MAIN

MAIN WASH

: Detergent

Clean the drawer.

20

Image 21

LG Electronics WD(M)-14220(5)FD, WD(M)-10220(5)FD XAMmax, No Water Supply, Detergent Does Not Flow In, Pre+Main Main Wash

Contents

SERVICE MANUAL e-mail http//LGEservice.com/techsup.htmlWASHING MACHINE P/No.3828ER3018U AUG. 2003 PRINTED IN KOREACONTENTS 1. SPECIFICATION 2-1.FEATURES 2. FEATURES & TECHNICAL EXPLANATIONJumbo drum More economical by Intelligent Wash System2-3.WATER LEVEL CONTROL 2-2.DETERMINE WASHING TIME BY FUZZY LOGIC2-4.THE DOOR CAN NOT BE OPENED water temperatureLowerAdjustablecoverfeetcap ACCESSORIES3. PARTS IDENTIFICATION DrainDoorplugpumpfilter128004. INSTALLATION CONNECT POWER PLUG HOW TO CONNECT INLET HOSECheck that the rubber washer is inside of the valve connector Connect the power plug to the wall outletTEST OPERATION Water temperature selector 5. OPERATIONWash program selector LED displayPower button Time DelayChild - Lock Spin buttonMAIN PWBDD 6. WIRING DIAGRAM / PROGRAM CHART7-1.BEFORE PERFORMING SERVICE 7. TROUBLESHOOTING7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY 7-2.QC TEST MODE7-4.ERROR DISPLAY SYMPTOMCAUSE ERROR SYMPTOM MAIN PWB ASSEMBLY is out of orderCAUSE 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION 8. ERROR DIAGNOSIS AND CHECK LISTSYMPTOM GUIDE FOR SERVICE CALLGUIDE FOR SERVICE CALL SYMPTOMCheck if the door switch is O.K Close the doorGUIDE FOR SERVICE CALL SYMPTOMClean the compartment for softener LOW-SUDSING8-2.FAULT DIAGNOSIS AND TROUBLESHOOTING NO POWERNONO NO WATER SUPPLY XAMmaxDETERGENT DOES NOT FLOW IN PRE+MAIN MAIN WASHSOUND XAMmaxReplace the STATOR ASSEMBLY or ROTOR ASSEMBLY of the INLET VALVE ASSEMBLY? YESReplace the S.PRESSURE SWITCH ASSEMBLY Replace the MAIN PWB ASSEMBLY MAINPWBASSEMBLY12Remove foreign material Reconnect or repair the connector Repair the DRAIN HOSE ASSEMBLYConnector HoseGray between HEATERASSEMBLYNormalReplacethe 10~30When pressing Opt.2, Spin and POWER buttons at SPIN TROUBLEthe same time after power off, press the Start/Pause Replace the MAIN PWB ASSEMBLYCONTROL PANEL ASSEMBLY Hook9. DISASSEMBLY INSTRUCTIONS DISPENSER ASSEMBLY DISPENSER ASSEMBLYPUSH OptionINLET VALVE ASSEMBLY3Option2 LOWER COVERGASKET DOOR ASSEMBLYClean the drain pump filter DamperHinge DRAIN PUMP ASSEMBLY HEATER ASSEMBLYTHERMISTOR WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB SWITCH ASSEMBLY, DOOR LOCKTake apart the CLAMP ASSEMBLY cabinet and release the GASKET Unscrew 2 screws holding the DOOR SWITCH ASSEMBLYA103 10. EXPLODED VIEW AND PART LISTA140 10-1.THE A153PART LIST OF CABINET ASSEMBLYF324 F321 F300 F320 F225 F220 10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSEMBLYF436 F431 F441 F430K346 10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLYK540 K344