Manuals / LG Electronics / Laundry Appliance / Washer

LG Electronics WD(M)-12220(5)FD, WD(M)-14220(5)FD, WD(M)-10220(5)FD, 16221FD Door Assembly, Gasket

Models: 16221FD 10220(5)FDB(N)

1 36

Download 36 pages 20.86 Kb

Page 30

DOOR ASSEMBLY

DOOR ASSEMBLY

Open the door completely.

Remove the two screws from the hinge.

When removing the DOOR ASSEMBLY, it is necessary to hold the BRACKET that is inner of the

CABINET COVER.

GASKET

Take apart the CLAMP ASSEMBLY (cabinet).

Unscrew 2 screws from the CABINET COVER.

Open the lower cover cap and unscrew 1 screw inside

Take apart the LOWER COVER.

Disassemble the CONTROL PANEL ASSEMBLY. (Refer to page 26)

Unscrew all the screws on the upper and lower sides of the CABINET COVER.

Take apart the tub CLAMP ASSEMBLY

Make sure that the drain hole of the GASKET is put beneath when reassembling the GASKET.

Refer to the arrow mark on the TUB COVER.

29

Image 30

LG Electronics WD(M)-12220(5)FD, WD(M)-14220(5)FD, WD(M)-10220(5)FD, 16221FD, 14220(5)FDB(N) Door Assembly, Gasket

Contents

SERVICE MANUAL e-mail http//LGEservice.com/techsup.htmlWASHING MACHINE AUG. 2003 PRINTED IN KOREA P/No.3828ER3018UCONTENTS 1. SPECIFICATION Jumbo drum 2. FEATURES & TECHNICAL EXPLANATION2-1.FEATURES More economical by Intelligent Wash System2-4.THE DOOR CAN NOT BE OPENED 2-2.DETERMINE WASHING TIME BY FUZZY LOGIC2-3.WATER LEVEL CONTROL water temperature3. PARTS IDENTIFICATION ACCESSORIESLowerAdjustablecoverfeetcap DrainDoorplugpumpfilter128004. INSTALLATION Check that the rubber washer is inside of the valve connector HOW TO CONNECT INLET HOSECONNECT POWER PLUG Connect the power plug to the wall outletTEST OPERATION Wash program selector 5. OPERATIONWater temperature selector LED displayChild - Lock Time DelayPower button Spin button6. WIRING DIAGRAM / PROGRAM CHART MAIN PWBDD7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY 7. TROUBLESHOOTING7-1.BEFORE PERFORMING SERVICE 7-2.QC TEST MODE7-4.ERROR DISPLAY SYMPTOMCAUSE ERROR SYMPTOM MAIN PWB ASSEMBLY is out of orderCAUSE SYMPTOM 8. ERROR DIAGNOSIS AND CHECK LIST8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION GUIDE FOR SERVICE CALLCheck if the door switch is O.K SYMPTOMGUIDE FOR SERVICE CALL Close the doorClean the compartment for softener SYMPTOMGUIDE FOR SERVICE CALL LOW-SUDSING8-2.FAULT DIAGNOSIS AND TROUBLESHOOTING NO POWERNONO DETERGENT DOES NOT FLOW IN XAMmaxNO WATER SUPPLY PRE+MAIN MAIN WASHReplace the STATOR ASSEMBLY or ROTOR ASSEMBLY XAMmaxSOUND of the INLET VALVE ASSEMBLY? YESRemove foreign material Reconnect or repair the connector MAINPWBASSEMBLY12Replace the S.PRESSURE SWITCH ASSEMBLY Replace the MAIN PWB ASSEMBLY Repair the DRAIN HOSE ASSEMBLYConnector HoseGray NormalReplacethe HEATERASSEMBLYbetween 10~30the same time after power off, press the Start/Pause SPIN TROUBLEWhen pressing Opt.2, Spin and POWER buttons at Replace the MAIN PWB ASSEMBLYCONTROL PANEL ASSEMBLY Hook9. DISASSEMBLY INSTRUCTIONS PUSH DISPENSER ASSEMBLYDISPENSER ASSEMBLY OptionLOWER COVER INLET VALVE ASSEMBLY3Option2DOOR ASSEMBLY GASKETClean the drain pump filter DamperHinge DRAIN PUMP ASSEMBLY HEATER ASSEMBLYTHERMISTOR Take apart the CLAMP ASSEMBLY cabinet and release the GASKET SWITCH ASSEMBLY, DOOR LOCKWHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB Unscrew 2 screws holding the DOOR SWITCH ASSEMBLYA140 10. EXPLODED VIEW AND PART LISTA103 10-1.THE A153PART LIST OF CABINET ASSEMBLYF436 F431 F441 10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSEMBLYF324 F321 F300 F320 F225 F220 F430K540 10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLYK346 K344