Manuals / Liebert / Computer Equipment / Network Card

Liebert XDK Manual Closing, Manual Opening, Push door evenly shut. Both magnetic locks must latch

Models: XDK

1 32

Download 32 pages 28.47 Kb

Page 12

Image 12

Description

3.4.3Manual Closing

1.Press LED switch for electromagnet activation

2.The LED lights up

3.Push door evenly shut. Both magnetic locks must latch.

3.4.4Manual Opening

1.Press LED switch - green LED doesn’t light

2.Rack door opens itself

Page 12

Image 12

Liebert XDK user manual Manual Closing, Manual Opening, Press LED switch for electromagnet activation 2. The LED lights up

Contents

Liebert XDK Rack Enclosure With Integrated Water-Based Cooling User Manual-17kWPrecision Cooling For Business-Critical ContinuityIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSTABLE OF CONTENTS 5.0 INSTALLATION AND COMMISSIONING6.0 SERVICING AND MAINTENANCE 1.0 INTRODUCTION 2.0 OPERATING CONDITIONSFIGURES TABLES1.0 INTRODUCTION 2.1 Proper Application 2.0 OPERATING CONDITIONSGeneral operating data 3.1 General function 3.0 DESCRIPTIONAir Duct WarmRear Front19 Equipment Side of XDK3.2.1 Data Overview-XDK Technical dataXDK general data Description3.3 Control 3.4 Automatic Door OpeningFigure 3 XDK door and automatic opening mechanism 3.4.1 Function 3.4.2 Initial CommissioningFigure 4 Door locking mechanisms, opening switch 3.4.3 Manual Closing 3.4.4 Manual Opening1. Press LED switch for electromagnet activation 2. The LED lights up 1. Press LED switch - green LED doesn’t lightSAFETY INFORMATION 4.1 Packaging Material4.2 Handling 4.0 EQUIPMENT INSPECTION, HANDLING AND STORAGE4.3 Storage 4.4 Returning the Unit in Case of Damage5.1 Preparation for Installation 5.0 INSTALLATION AND COMMISSIONING5.2 Positioning the XDK 5.2.1 Remove Recirculation Air Duct Transport Lock5.3 Water Connection 5.3.1 Preparing Heat Exchanger for Initial CommissioningFigure 6 Heat exchanger access Figure 7 Control valveInstallation and Commissioning Top ViewFigure 8 Heat exchanger Figure 9 Heat exchanger connectionPreparations for Connecting 5.4 Condensed Water ConnectionFigure 10 Bottom plate with cutouts Rear5.5 Electrical Connection 5.6 Sealing the CabinetThe units fans will rotate clockwise 6.0 SERVICING AND MAINTENANCE 6.1.1 Fan Replacement6.1 General Inspection on Fans-Annual Figure 11 Replacing a fan6.2 Inspect the Heat Exchanger-Annual Reinstall the fan by reversing the steps to remove the fan6.3 Replacing the Heat Exchanger Figure 12 Heat exchanger replacementRegularly check the condensed water drain and clean if necessary Servicing and Maintenance7.0 DISMANTLING AND DISPOSAL Dismantling and Disposal8.0 WATER PURITY REQUIREMENTS Prevalent impurities and removal methodsSuggested hydrologic levels 8.1 Unit Installation Checklist Comments8.2 Commissioning Certificate Nominal values at setup siteTable 6 XDK - Commissioning certificate Nominal values keptConfiguration Table 8 Type of cabinetControl of status Water Purity RequirementsTable 10 Cold water facility on site Table 11 Electrical data / documentsTable 12 Function check Water Purity RequirementsCommissioning performed by day to day operating Correctness of function check protocol certified byTable 12 Function check continued Water Purity RequirementsWater Purity Requirements Page Ensuring The High Availability 0f Mission-Critical Data And ApplicationsNe t ti n