Liebherr 110309 7084282 - 01 Fitting the unit doors, For 600 mm-wide recess

Putting into operation

u Vertically align the appliance by means of the adjustable- height feet Fig. 8 (25), using the accompanying open-ended spanner Fig. 8 (26).

w The appliance is now correctly positioned in depth. The dis- tance from the front edge of the side wall of the unit to the appliance body is 42 mmall the way round. (Allow for door stop components, such as knobs and sealing lips.)

Note

Incorrect installation will lead to malfunction!

If the distance is not kept, the door may not close. This may lead to icing, to condensate forming and to malfunction.

u Be sure to keep to the clearance of 42 mm all the way round. (Allow for door stop components, such as knobs and sealing lips.)

Tightly screw the appliance into place in the recess: u At the top and bottom of

both doors with Spax screws Fig. 17 (28) passed through the hinge plates.

On the handle side at the top:				Fig. 17
u Loosen		the	screws
	Fig. 18 (55) a little.
u Tightly		screw	the top
	mounting		bracket
	Fig. 18 (50) to the unit wall
	using	Spax	screw
	Fig. 18 (29) ø4x19.
u Break off the projecting
	end	of the	cover	Fig. 18
	Fig. 18 (53).
u Tighten the screws Fig. 18 (55).
u Put on the cover Fig. 18 (53).
On the handle side at the bottom:
u Loosen		the	screws
	Fig. 19 (51) a little.
u Tightly screw the bottom
	mounting		bracket
	Fig. 19 (50) to the unit wall
	using	Spax	screw
	Fig. 19 (29) ø4x19.
u Break off the projecting end
	of the cover Fig. 19 (53). It
	is no longer required.
u Tighten		the	screws
	Fig. 19 (51).			Fig. 19
u	Put the cover Fig.19 (54) on

the bottom mounting brack- et Fig. 19 (50).

u Close the appliance door.

4.3.2 Fitting the unit doors

Fig. 20 The fitting aids Fig.20 (30) are required for both doors. There- fore fit the unit doors one after the other.

uCheck 8 mm-presetting. (Distance between appliance door and lower edge of crosspiece)

uSlide up the assembly aids Fig.20 (30) to the height of the unit door. Lower stop edge ▲of the assembly aid = upper edge of the unit door to be fitted.

uUnscrew the cross- piece Fig. 21 (31) by undoing the locknuts Fig. 21 (32).

uAttach the cross- piece Fig. 21 (31) to- gether with the as-

sembly aids Fig. 21 (30) to the in- side of the unit door.

Fig. 21

For 600 mm-wide recess:

u Concentrically align the crosspiece Fig. 21 (31): Mark a short centre line on the unit door and put the tip of the arrow on the crosspiece over it.

w Distances to the outer edge are equal at the left and right.

For particle board doors:

u Tightly screw the crosspiece Fig. 21 (31) into place using at least 6 screws Fig. 21 (41).

For frame and panel doors:

u Tightly screw the crosspiece Fig. 21 (31) into place using 4 screws Fig. 21 (41) at the edge.

u Raise and remove the assembly aids Fig. 21 (30), turn them and slide them into the adjacent openings.

Fig. 22 u Attach the unit door to the adjusting bolts Fig. 22 (33) and loosely screw the locknuts Fig. 22 (32) onto the adjusting

bolts.

u Close the door.

u Check the gap between the door and the surrounding unit doors.

u To laterally align the unit door: Move the unit door in the X direction.

u Align unit door in height and lateral inclination: Adjust the ad- justing bolts Fig. 22 (33) using a screwdriver.

w The unit door is flush and in alignment with the surrounding unit fronts.

u Tighten the lock nuts Fig. 22 (32). Ensure that both metal

edges are flush (sym- bol //):

u Drill pilot holes in the door of the unit (possi- bly make preliminary hole with a bradawl).

Fig. 23 u Screw the appliance door to the unit door with screws Fig. 23 (41) passed through the mounting brackets

Fig. 23 (34).

8