Liebherr 7084284-03 installation instructions Fitting the unit doors

Putting into operation

u Fit the equaliser trim Fig. 10 (20) concentri- cally onto the appliance: Slide it into the recess and engage it in the keyholes.

Fig. 10

u Screw all the mounting brackets Fig. 11 (34) to the pre-drilled holes in the appliance door using hexagon screws Fig. 11 (35).

Fig. 11

For 16 mm -thick unit walls
= 568 mm-wide recess:
u Clip spacer Fig. 12 (23) onto
the upper hinge and spacer
Fig. 8 (24) onto the lower
hinge.						Fig. 12
u Attach	the	top cover
Fig. 13 (53) and bottom
cover Fig. 13 (50) to the
mounting brackets.
u Fasten	the	mounting
brackets Fig. 13 (50) at the
top and bottom with screws
Fig. 13 (51) so that the
brackets can still be moved
a little to the left and right.						Fig. 13
u Strip the protective film off the cover trim
Fig. 14	(22).	Apply	the	cover	trim
Fig. 14 (22) to the projection of the cover
Fig. 13 (53) on the handle side, flush with
the front, and adhesively affix it to the side
wall of the appliance.			the	cover	strip
u If necessary,		shorten				Fig. 14
Fig. 14 (22) at the bottom: The cover strip
Fig. 14 (22) has to end 3 mm above the
upper edge of the lower mounting bracket
Fig. 8 (50).

Slide in and align the appliance:

u Slide in the appliance until the covers Fig. 13 (53)abut Fig. 13 against the side wall of the kitchen unit.

u Extend the adjustable foot.

For 16 mm-thick unit walls = 568 mm-wide recess:

u Allow the spacers to abut against the side wall of the kitchen unit.

Fig. 15

For 19 mm-thick unit walls =

562 mm-wide recess:

u Align the front edges of the hinges so as to be flush with the side wall of the kitchen unit.

Fig. 16

For kitchen units (16 mm and 19 mm ) with door stop components (knobs, sealing lips etc.):

u Allow for the extra distance (depth of the door stop compo- nents): Allow hinges and covers Fig. 13 (53) to protrude by the extra distance.

All appliances:

u Vertically align the appliance by means of the adjustable- height feet Fig. 8 (25), using the accompanying open-ended spanner Fig. 8 (26).

w The appliance is now correctly positioned in depth. The distance from the front edge of the side wall of the unit to the appliance body is 42 mm all the way round. (Allow for door stop components, such as knobs and sealing lips.)

Note

Incorrect installation will lead to malfunction!

If the distance is not kept, the door may not close. This may lead to icing, to condensate forming and to malfunction.

u Be sure to keep to the clearance of 42 mm all the way round. (Allow for door stop components, such as knobs and sealing lips.)

Tightly screw the appliance into place in the recess:
u At the top and bottom
of both doors				with
Spax			screws
Fig. 17		(28) passed
through		the		hinge
plates.
On the handle side at the top:						Fig. 17
u Loosen		the		screws
Fig. 18 (51) a little.
u Tightly		screw		the top
mounting				bracket
Fig. 18 (50) to the unit
wall	using		Spax		screw
Fig. 18 (29) ø4x19.
u Break off the projecting
end	of		the		cover	Fig. 18
Fig. 18 (53).
u Tighten the screws Fig. 18 (51).
u Put on the cover Fig. 18 (53).
On the handle side at the bottom:
u Loosen			the		screws
Fig. 19 (51) a little.
u Tightly screw the bottom
mounting				bracket
Fig. 19 (50) to the unit
wall	using		Spax		screw
Fig. 19 (29) ø4x19.
u Break off the projecting
end		of	the		cover
Fig. 19 (53). It is no longer
required.			the		screws
u Tighten
Fig. 19 (51).						Fig. 19
u Put the cover Fig. 19 (54)
on	the	bottom		mounting
bracket Fig. 19 (50).
u Close the appliance door.

4.5.2 Fitting the unit doors

Fig. 20

8