Liebherr 7084284-03 installation instructions Control

Control

uPut on and engage the covers Fig. 8 (5,6,7).

For appliances without soft stop mechanism adjust door stop cushioning:

The door stop cushioning can be adjusted if necessary using the accompanying Allen key:*

u For stronger spring force: turn clockwise.*

u For lesser spring force (as-deliv- ered): turn anticlockwise.*

u Attach the remaining covers to the hinges.*

*

Check the following points to ensure the appliance is fitted properly. Failure to do so may lead to icing, condensate forming and malfunction:

wThe door has to close properly

wThe unit door must not butt against the unit body

wThe seal must have a firm fit at the upper corner on the handle side. To check, darken the room, place a torch inside the appliance at the top and close the door. If light shines through, check the assembly.

4.6 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film! u Do not allow children to play with packing material.

The packaging is made of recyclable materials:

-corrugated board/cardboard

-expanded polystyrene parts

-polythene bags and sheets

-polypropylene straps

-nailed wooden frame with polyethylene panel*

uTake the packaging material to an official collecting point.

4.7 Connecting the appliance

NOTICE

Risk of damage to the electronic control system!

u Do not use stand-alone inverters (conversion of d.c. to a.c./ three-phase) or energy saving plugs.

WARNING

Fire and overheating hazard!

u Do not use extension cables or multiple socket outlets.

The type of current (alternating current) and voltage at the installation site have to conform with the data on the type plate (see Appliance at a glance).

Connect the appliance only with a properly installed socket outlet with earthing contact. The socket outlet must be fused with 10 A or higher.

It must be easily accessible so that the appliance can be quickly disconnected from the supply in an emer- gency. It must be outside the area of the rear of the appliance.

u Check the electrical connection. u Plug in the power plug.

4.8 Switching on the appliance

Note

u To switch on the entire appliance it is necessary only to switch on the freezer compartment.

Put the appliance into operation about 2 hours before first loading food to be frozen.

Do not load food to be frozen before the temperature display reads -18 °C.

4.8.1 Switching on the freezer compartment

uPress On/Off button, freezer compartment Fig. 2 (3). The refrigerator compartment temperature display the set temperature.

The temperature display of the freezer compartment

until the temperature is sufficiently low. If the temperature above 0 °C, dashes flash. If it is below, the set temperature

flashes.wshowswflashesis

4.8.2Switching on the refrigerator compart-

ment

uPress On/Off button, refrigerator compartment Fig. 2 (11). w The interior light is on when the door is open.

w The temperature display shines. The refrigerator compart- ment is switched on.*

5Control

5.1Brightness of the temperature display

You can adjust the brightness of the temperature display to the light conditions of the room in which the appliance is installed.

5.1.1 Adjusting the brightness

The brightness is adjustable between h1 (no illumination) and h5 (maximum luminosity).

u To activate the setting mode: press the SuperFrost button Fig. 2 (2) for about 5 s.

w The display indicates c.

w The SuperFrost button flashes.

u Using the Up setting button, freezer compartment Fig. 2 (5) or Down setting button, freezer compartment Fig. 2 (4), select h.

u To confirm: briefly press the SuperFrost button Fig. 2 (2).

u To make the display brighter: press Up button, freezer compartment Fig. 2 (5).

u To make the display darker: press Down button, freezer compartment Fig. 2 (4).

u To confirm: press SuperFrost button Fig. 2 (2). w The brightness is adjusted to the new value.

u To deactivate the set-up mode: press On/Off button, freezer compartment Fig. 2 (3).

-or-

u Wait for 5 minutes.

w The temperature is indicated again in the temperature display.

5.2 Child proofing

The child-proofing function enables you to make sure that the appliance is not inadvertently switched off by playing children.

5.2.1 Setting the child lock

u To activate the setting mode: press SuperFrost button Fig. 2 (2) for about 5 s.

10