Installation
For appliances with a fixed water supply for the IceMaker:*
u Connect the IceMaker as indicated the section entitled Water Supply.*
u Fit the locking clip Fig. 11 (62).*
Fig. 11 *
All appliances:
u Push the appliance 3/4 of the way into the recess. u Remove the covers Fig. 9 (5,6,7).
u Screw Fig. 12 (61) the equalizer trim Fig. 12 (20)to the appliance through the oblong holes on top.
u To shorten the trim Fig. 16 (22) at the bottom, if necessary: Position the cover Fig. 9 (54) on the bottom mounting bracket Fig. 15 (50) and shorten the trim Fig.16 (22) so that it is flush with the upper edge of the cover.
u Remove the cover Fig. 9 (54) again.
To slide the appliance in and align it: |
|
u Slide the appliance in until it comes into contact with the | |
covers Fig. 15 (53) on the side wall of the unit. Fig. 15 | |
With 5/8 '' (16 mm) thick unit |
|
walls = |
|
recess: |
|
u Allow the spacers on the side |
|
wall of the unit to butt up against | Fig. 17 |
the appliance. | |
With 3/4 '' (19 mm) thick unit |
|
walls = |
|
recess: |
|
u Align the front edges of the |
|
hinges flush with the side wall |
|
of the unit. | Fig. 18 |
u Fasten all mounting brackets Fig. 13 (34) with
hex head screws Fig. 13 (35) to the pre- bored holes in the appliance door.
Fig. 12
For units (5/8 '' (16 mm) and 3/4 '' (19 mm)) with door | |
stop components (knobs, sealing lips, etc.): | |
u Allow for the additional distance (depth | of door stop |
components). Allow the hinges and | the covers |
Fig. 15 (53) to protrude by the additional distance. |
All appliances:
u Adjust the adjustable feet Fig. 9 (25) with the supplied
With 5/8 '' (16 mm) thick unit | Fig. 13 | ||||
| |||||
walls = |
| ||||
recess: |
|
|
|
| |
u Clip a spacer Fig. 14 (23) onto |
| ||||
the upper hinges and a |
| ||||
spacer Fig.9 (24) onto the lower | Fig. 14 | ||||
hinges. |
|
|
| ||
u Attach the top and bottom |
| ||||
covers | Fig. 15 (53) to the |
| |||
mounting |
| brackets |
| ||
Fig. 15 (50). |
| mounting |
| ||
u Fasten | the |
| |||
brackets Fig. 15 (50) at the |
| ||||
top |
| with | screws |
| |
Fig. 15 (55) and at the |
| ||||
bottom | with | screws |
| ||
Fig. 9 | (51) | such that the |
| ||
bracket can still be moved |
| ||||
slightly to the left and to the | Fig. 15 | ||||
right. |
|
|
|
|
|
u Remove the protective film from the | |||||
trim | Fig. | 16 | (22).Attach the | trim |
Fig. 16 (22) on the handle side and flush with the front to the projecting edge of the cover Fig. 15 (53) and glue to the sidewall of the appliance.
Fig. 16
w The appliance is now correctly positioned in depth. The gap between the front edge of the side wall of the unit and the body of the appliance is
Note |
|
|
Malfunction due to incorrect assembly! | ||
If the spacing is not correct, the door may not close. This | ||
can cause icing up, the formation of condensate, and | ||
malfunctions. |
| |
u A continuous space of | ||
maintained. (Allow for door stop components, such as | ||
knobs and sealing lips.) | ||
To secure the appliance in the recess: | ||
u Screw | chipboard | |
screws | Fig. 19 (28) on | |
both doors at the top | ||
and at | the | bottom |
through | the | hinge |
plates. |
|
|
Fig. 19
On the handle side at the top:
10