MAINTENANCE | ||
| FIGURE D.4 |
|
|
|
|
|
|
|
|
|
| 4.68 (119 mm) | ||||||||||||
|
|
|
|
|
| GAS PLUG |
|
|
|
|
|
| PRESS HERE TO | ||||||||
|
|
|
|
|
|
|
|
|
|
|
| REMOVE THE CABLE | |||||||||
|
|
|
|
|
| OR FITTING |
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
| HANDLE NUT | |||||||||
| FEEDER END |
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| CONNECTOR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CABLE HANDLE NUT
TAIL PIECE
.43 (11 mm) MAX.
INCOMING
CONNECTOR
CONNECTOR COVER
CABLE BOOT
CABLE
CABLE HANDLE
STRAIN RELIEF HOUSING
STRAIN RELIEF
strands with the threaded end out. Assemble incom-
ing connector to cable by forcing the steel tube of j. Install and trim liner per Liner Installation Section. the connector into the inside diameter of the cable
inner tube until the copper strands are butted against the incoming connector shoulder. Keeping the copper strands against the shoulder, pull the connector nut over the copper strands, engage the incoming connector threads, and tighten in place. Refer to Figure 3.
note: For best results, insert a .219"/.240" (5.6/6.1
mm)diameter rod through the connector and into core of cable approximately 5.00” (127 mm) when pushing the connector tube into the cable core tube. To tighten, hold the connector in place while turning the nut. then remove the rod from the core. This procedure ensures the inner core does not kink while assembling or tightening.
Position the plastic strain relief such that the tapered end is 4.68 (119 mm) from the incoming connector (see Figure 5). Lock into place with steel housing. Plastic strain relief may overhang cable jacket a maximum of .43" (11 mm).
g.Position cable boot and cable handle on cable and assemble replacement control wire terminals in place on the cable handle. Insert connector cover in place. Install tailpiece and fasten to cable handle with cable handle nut. Refer to Figure 5.
h.Replace the molded gas plug (or barbed fitting) and feeder end connector.
MAGNUM® PRO 250, 350, 450 & 550 AMP
