Lincoln Electric IM732-B Connection of Wire Feeders to V350-PRO CE, Remote Control of Invertec

				INSTALLATION			A-3
A-3
LN-15 Connection Instructions					• If a remote control such as K857 is to be used with
	• Turn the Invertec® power switch "off".				the LN-742, the remote can be connected directly
	• Connect the electrode cable to the output terminal of				to the 6-pin MS-style connector on the front of the
	polarity required by electrode. (See Figures below)				Invertec® or use a K864 adapter to connect the LN-
					742 and the remote to the 14-pin MS-style connector.
		ACROSS THE ARC MODEL
	RANGER 9, RANGER 300 DLX	Output Terminals
		Always Hot.
	COMMANDER 300	"ON" position or use a	wire feeder		Cobramatic Connection Instructions
	RANGER 2V35050
	V350-PRO	Power source contactor
	COMMANDER 500	switch must be in the	semiautomatic		•	Turn the Invertec® power switch "off"
	RANGER 305G	K848 Junper Plug Kit.	K1870-1
	TWIST-MATE	Electrode Cable		Work	•	Connect the control cable from the Cobramatic to
						the 14-pin MS-style connector.
				Clamp
					•	Connect the electrode cable to the output terminal
						of the polarity required by electrode. Connect the
		CONTROL CABLE MODEL				work lead to the other terminal.
					• Set the meter polarity switch on the front of the
						Invertec® to coincide with wire feeder polarity
		Electrode Cable				used.
					•	If a remote control	such as K857 is to be used
						with the Cobramatic, the remote can be connected
						directly to the 6-pin MS-style connector on the front
						of the Invertec® or use a K864 adapter to connect
	• Set the meter polarity switch on the front of the Invertec®					the cobramatic and the remote to the 14-pin MS-
	to coincide with wire feeder polarity used.					style connector.

LN-25 Connection Instructions

•Turn the Invertec® power switch "off".

•Connect the electrode cable to the output terminal of polarity required by electrode. Connect the work lead to the other terminal.

•LN-25 with Remote Control options can be used with the "CE" version of the V350. The 6-Pin (K444-1) and 14-pin (K444-2) remotes can be connected directly to the 6-pin & 14-pin MS-style connector. The 42 Volt Remote Voltage and Output Control (K624-1) Kit can be connect- ed to the V350’s 14-pin MS-style connector using Remote Control Cable assembly K627- [ ]. LN-25s with a K431-1 remote kit can be connected to the V350’s 14-pin MS-style connector using a K432 cable and K876 adapter. (See connection diagram S19899). Or the K432 cable could be modified with a K867 Universal Adapter Plug (See connection diagram S19405) to connect it to the V350’s 14-pin MS-style connector.

LN-742 Connection Instructions

•Turn the Invertec® power switch "off"

•Either a K591 or a K593 Input cable assembly is required to connect the LN-742 to the Invertec®.

•Connect the control cable from the LN-742 to the 14-pin MS-style connector.

•Connect the electrode cable to the output terminal of the polarity required by electrode. Connect the work lead to the other terminal.

•Set the meter polarity switch on the front of the Invertec® to coincide with wire feeder polarity used. The wire feeder will now display the welding volt- age.

CONNECTION OF WIRE FEEDERS TO V350-PRO (CE)

Wire feeders other than these listed may be used pro- vided that the auxiliary power supply capacity of the Invertec® is not exceeded. K867 Universal Adapter Plug may be required. See connection diagram S24985 on page F-4.

REMOTE CONTROL OF INVERTEC®

Remote Control K857, Hand Amptrol K963 and Foot Amptrol K870.

UNDERCARRIAGE MOUNTINGS

MOUNTING HOLE LOCATIONS

NOTE: MOUNTING SCREWS CAN NOT PROTRUDE MORE THAN 0.5 INCHES INSIDE THE MACHINE.

3.50

1/4-20 NUT (4 PLACES) 5.50

10.00

11.84 4/01

M19527

INVERTEC® V350-PRO (CE)