OPERATION | ||
|
|
|
POWER MODE™
The Power Mode™ process was developed by Lincoln to maintain a stable and smooth arc at low procedure settings which are needed to weld thin metal without
•Short Arc MIG at low procedure settings.
•Aluminum MIG welding.
Power Mode™ is a method of high speed regulation of the output power whenever an arc is established. It provides a fast response to changes in the arc. The higher the Power Mode Setting, the longer the arc. If a welding procedure is not established, the best way to determine the Power Mode Setting is by experimenta- tion until the desired output result is established.
In the Power Mode two variables need to be set:
•Wire Feed Speed
•Power Mode Trim
Setting up a Power Mode procedure is similar to set- ting a CV MIG procedure. Select a shielding gas appropriate for a short arc process.
•For steel, use 75/25 Ar/CO2 shield gas.
•For Stainless, select a Helium blend
•For Aluminum, use 100% Ar.
Start by setting the wire feed speed based upon mate- rial thickness and appropriate travel speed. Then adjust the Volts/Trim knob as follows:
•For steel, listen for the traditional “frying egg” sound of a good
•For aluminum, simply adjust the Volts/Trim knob until the desired arc length is obtained.
Note the Volts/Trim display is simply a relative number and DOES NOT correspond to voltage.
Some procedure recommendations appear in Table B.3.
Recommended Welding Procedures for Power Mode - Table B.3
| MATERIAL | Aluminum 4043 | Aluminum 5356 | Mild Steel | Mild Steel | Mild Steel | Mild Steel | Mild Steel | Mild Steel | Stainless Steel | Stainless Steel | |
|
|
|
|
|
|
|
|
|
|
|
| |
| WIRE | E4043 | E5356 | L56 | L56 | L56 | L56 | L56 | L56 | E308L | E308L | |
|
|
|
|
|
|
|
|
|
|
|
| |
| WIRE SIZE | 0.035 | 0.035 | 0.025 | 0.025 | 0.030 | 0.030 | 0.035 | 0.035 | 0.030 | 0.035 | |
|
|
|
|
|
|
|
|
|
|
|
| |
| GAS | 100% Ar. | 100% Ar. | 100% CO2 | 75/25 Ar/CO2 | 100% CO2 | 75/25 Ar/CO2 | 100% CO2 | 75/25 Ar/CO2 | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
THICKNESS | SETTINGMODE | 22 ga. |
|
| Not Recommended | 100 / 0.8 | Not Recommended | 90 / 1.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 20 ga. |
|
| 120 / 1.0 | 120 / 1.0 | 100 / 0.7 | 100 /1.0 |
|
| 80 / 1.5 | 50 / 0.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 18 ga. |
|
| 140 / 1.7 | 140 / 1.5 | 110 / 1.5 | 110 / 1.5 | 100 / 2.5 | 100 / 2.5 | 110 / 2.0 | 110 / 2.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 16 ga. |
|
| 190 / 2.0 | 190 / 2.0 | 125 / 2.0 | 125 / 2.0 | 125 / 3.0 | 125 / 3.0 | 140 / 2.5 | 130 / 2.7 |
|
|
|
|
|
|
|
|
|
|
|
|
|
MATERIAL | /WFSPOWER | 14 ga. | 400 / 2.0 | 400 / 2.5 | 260 / 3.0 | 260 / 3.0 | 160 / 2.3 | 160 / 2.3 | 160 / 3.8 | 160 / 3.5 | 210 / 3.0 | 190 / 3.5 |
|
|
|
|
|
|
|
|
|
|
| ||
3/16 | 570 / 9.0 | 600 / 7.8 | 330 / 5.0 | 330 / 4.5 | 400 / 7.5 | 400 / 7.0 | 200 / 5.0 | 200 / 4.5 | 270 / 5.0 | 230 / 6.0 | ||
|
| 12 ga. |
|
| 230 / 3.5 | 230 / 3.5 | ||||||
|
| 10 ga. | 500 / 7.0 | 500 / 7.0 |
|
| 300 / 6.0 | 300 / 6.0 | 240 / 6.5 | 240 / 7.0 | 325 / 6.5 | 300 / 7.0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1/4 | 700 / 9.1 | 700 / 8.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Not | Not |
|
|
|
|
|
|
|
|
COMMENTS | Recommended | Recommended |
|
|
|
|
|
|
|
| ||
below 400 | below 400 |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| WFS | WFS |
|
|
|
|
|
|
|
|
