TOC

F-3

F-3

TROUBLESHOOTING & REPAIR

PC BOARD TROUBLESHOOTING PROCEDURES

Return to Section

Return to Section TOC

TOC

Return to Master

Return to Master TOC

TOC

WARNING

ELECTRIC SHOCK can kill.

•Have an electrician install and service this equipment. Turn the input power OFF at the fuse box before working on equipment. Do not touch electrically hot parts.

CAUTION

Sometimes machine failures appear to be due to PC board failures. These problems can sometimes be traced to poor electrical connections. To avoid prob- lems when troubleshooting and replacing PC boards, please use the following procedure:

1.Determine to the best of your technical ability that the PC board is the most likely component causing the failure symptom.

2.Check for loose connections at the PC board to assure that the PC board is properly connected.

3.If the problem persists, replace the suspect PC board using standard practices to avoid static electrical damage and electrical shock. Read the warning inside the static resistant bag and perform the following procedures:

PC board can be damaged by static electricity.

-Remove the PC board from the static-shielding bag and place it directly into the equipment. Don’t set the PC board on or near paper, plastic or cloth which could have a static charge. If the PC board can’t be installed immediately, put it back in the static-shield- ing bag.

-If the PC board uses protective shorting jumpers, don’t remove them until installation is complete.

-If you return a PC board to The Lincoln Electric Company for credit, it must be in the static-shielding bag. This will prevent further damage and allow prop- er failure analysis.

4.Test the machine to determine if the failure symptom has been corrected by the replacement PC board.

NOTE: It is desirable to have a spare (known good) PC board available for PC board troubleshooting.

NOTE: Allow the machine to heat up so that all electrical components can reach their operating temperature.

5.Remove the replacement PC board and substitute it with the original PC board to recreate the original problem.

a.If the original problem does not reappear by substituting the original board, then the PC board was not the problem. Continue to look for bad connections in the control wiring harness, junction blocks, and terminal strips.

ATTENTION

Static-Sensitive

Devices

Handle only at

Static-Safe

Workstations

-Remove your body’s static charge before opening the static- shielding bag. Wear an anti-static wrist strap. For safety, use a 1 Meg ohm resistive cord connected to a grounded part of the equipment frame.

-If you don’t have a wrist strap, touch an un-painted, grounded, part of the equipment frame. Keep touching the frame to prevent static build-up. Be sure not to touch any electrically live parts at the same time.

b. If the original problem is recreated by the substitution of the original board, then the PC board was the problem. Reinstall the replacement PC board and test the machine.

6.Always indicate that this procedure was followed when warranty reports are to be submitted.

NOTE: Following this procedure and writing on the warranty report, “INSTALLED AND SWITCHED PC BOARDS TO VERIFY PROBLEM,” will help avoid denial of legitimate PC board warranty claims.

-Tools which come in contact with the PC board must be either conductive, anti-static or static-dissipative.

POWER MIG 300

Page 46 Page 48
Page 47
Image 47
Lincoln Electric SVM160-B service manual PC Board Troubleshooting Procedures
Page 46 Page 48

SVM160-B specifications

The Lincoln Electric SVM160-B is a standout model in the realm of portable arc welders, designed specifically for light to medium-duty welding tasks. As part of Lincoln Electric’s renowned line of welding equipment, the SVM160-B combines efficiency with durability, catering to both professional welders and hobbyists alike.

One of the primary features of the SVM160-B is its lightweight and compact design. Weighing in at just around 60 pounds, it offers excellent portability, allowing users to easily transport the unit to various job sites. This mobility is enhanced by an integrated handle and a rugged construction, making it suitable for both indoor and outdoor applications.

The SVM160-B utilizes advanced inverter technology, which significantly enhances its performance capabilities. This technology not only contributes to the welder's energy efficiency but also allows for a more stable arc, reducing spatter and resulting in cleaner welds. The machine can operate on both 120V and 240V power sources, providing flexibility for users to adapt to different settings and requirements.

Among its key characteristics, the SVM160-B features a welding output range that accommodates various welding needs, allowing users to achieve welds from 20 to 160 amps. This versatility makes it ideal for welding different materials, including mild steel, stainless steel, and aluminum. Furthermore, the unit supports a range of welding processes, including MIG, stick, and TIG welding, enhancing its adaptability for various projects.

Another highlight of the SVM160-B is its user-friendly interface. The control panel is designed to facilitate ease of use, with clearly marked dials and indicators that enable quick adjustments of settings. This intuitive design ensures that both novice and experienced users can operate the machine efficiently and effectively.

Safety features are also a crucial aspect of the SVM160-B. It comes equipped with thermal overload protection, which prevents the unit from overheating during extended use. This built-in safeguard extends the welder's lifespan and enhances user safety.

In summary, the Lincoln Electric SVM160-B is a versatile, portable welder that combines advanced technology with user-friendly features, making it an excellent choice for a wide range of welding applications. Its lightweight design, inverter technology, and robust safety features make it a reliable option for both professionals and enthusiasts. Whether tackling small repairs or larger projects, the SVM160-B stands ready to deliver quality results.
Top Page Image Contents