Manuals / Linksys / Computer Equipment / Network Router

Linksys AG300 manual Bridged Mode Only, Optional Settings required by some ISPs, Network Setup

Models: AG300

1 78

Download 78 pages 1.91 Kb

Page 23

Bridged Mode Only

ADSL Gateway

Bridged Mode Only

If you are using your Gateway as a bridge, which makes the Gateway act like a stand-alone modem, select Bridged Mode Only. All NAT and routing settings are disabled in this mode.

Optional Settings (required by some ISPs)

•Host Name and Domain Name. These fields allow you to supply a host and domain name for the Gateway. Some ISPs require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, you can leave these fields blank.

•MTU and Size. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Select Manual and enter the value desired in the Size field. It is recommended that you leave this value in the 1200 to 1500 range. By default, MTU is configured automatically.

Network Setup

•Router IP. The values for the Gateway’s Local IP Address and Subnet Mask are shown here. In most cases, keep the default values.

•Local IP Address. The default value is 192.168.1.1.

•Subnet Mask. The default value is 255.255.255.0.

•Network Address Server Settings (DHCP). Configure the Gateway’s Dynamic Host Configuration Protocol (DHCP) settings in this section.

•Local DHCP Server. A Dynamic Host Configuration Protocol (DHCP) server automatically assigns an IP address to each computer on your network for you. Unless you already have one, it is highly recommended that you leave the Gateway enabled as a DHCP server. You can also use the Gateway in DHCP Relay mode.

•DHCP Relay Server. If you enable the DHCP Relay mode for the Local DHCP Server setting, enter the IP address for the DHCP server in the fields provided.

•Advanced: This button displays a window that lets you reserve addresses in the DHCP range for particular machines.

•Autodetect LAN DHCP Server: Enable this function if you already have a DHCP server on your LAN and you wish to continue using it.

Chapter 5: Configuring the ADSL Gateway

Figure 5-9: Bridged Mode Only

Figure 5-10: Optional Settings

17

The Setup Tab

Image 23

Linksys AG300 manual Bridged Mode Only, Optional Settings required by some ISPs, Network Setup

Contents

Model No. AG300 ADSL GatewayUser Guide word definition How to Use this GuideCopyright and Trademarks Table of Contents ADSL Gateway Appendix F Warranty InformationAppendix G Regulatory Information Appendix H Contact InformationList of Figures Figure 5-25 List of PCs Welcome Chapter 1 IntroductionWhat’s in this User Guide? What’s in this User Guide? Appendix H Contact InformationADSL Gateway Chapter 1 Introductionip internet protocol a protocol used to send data over a network Chapter 2 Planning Your NetworkThe Gateway’s Functions IP AddressesDynamic IP Addresses DHCP Dynamic Host Configuration Protocol ServersPorts and Reset Button on Side Panel Chapter 3 Getting to Know the ADSL GatewayLEDs on Side Panel The Bottom Panel Overview Chapter 4 Connecting the ADSL GatewayConnecting the Gateway to a Computer 5. Power on one of your computers that is connected to the Gateway Setup Chapter 5 Configuring the ADSL GatewayApplications & Gaming Access RestrictionsAdministration SecurityInternet Setup How to Access the Web-based UtilityThe Setup Tab The Basic Setup TabStatic IP RFC 1483 Bridged Dynamic IPIPoA RFC 1483 RoutedRFC 2364 PPPoA RFC 2516 PPPoENetwork Setup Bridged Mode OnlyOptional Settings required by some ISPs DDNS The DDNS TabTZO.com DynDNS.orgAdvanced Routing The Advanced Routing TabPVC Routing Policy ADSL Gateway To disable the line’s criteria, click the box to clearChapter 5 Configuring the ADSL Gateway The Setup TabAdditional Filters The Security TabThe Firewall Tab FirewallIPSec VPN Tunnel The VPN TabVPN Passthrough Delete Click this button to delete the selected tunnel Other Settings The Internet Access Tab The Access Restriction TabThen enter the range of ports you want to filter Single Port Forwarding The Applications & Gaming TabThe Single Port Forwarding Tab The Port Range Forwarding Tab The DMZ Tab The Port Triggering TabPVC QoS Priority Edit list of QoS SettingsThe QoS Tab Fragment packets’ size of AF and BE traffic to be equal to the size of EF traffic Enable this option and input a packet size to have large Assured Forwarding medium priority and Best Effort low priority packets fragmented so they will not uduly delay Expedited Forwarding high priority packets. The value you enter should be from 68 to The Management Tab The Administration TabGateway Access IGMP-Proxy SNMPUPnP IGMP-Snooping Email Alerts The Reporting TabReporting Restore Configuration The Diagnostics TabThe Backup&Restore Tab Backup ConfigurationUpgrade from LAN The Factory Defaults TabThe Firmware Upgrade Tab The Reboot TabInternet Connection The Status TabThe Gateway Tab Gateway InformationADSL Gateway The Local Network TabFigure 5-43 Local Network Figure 5-44 DHCP Active IP Table Figure 5-45 ARP/RARP TablePVC Connection The DSL Connection TabDSL Status 1. I need to set a static IP address on a computer Appendix A TroubleshootingCommon Problems and Solutions 2. I want to test my Internet connection 9. Restart the computer if asked For Windows XP3. I am not getting an IP address on the Internet with my Internet connection 2. Enter any name you want to use for the Customized Application Page Follow these steps to set DMZ hosting 8. I can’t get the Internet game, server, or application to work14. My DSL service’s PPPoE is always disconnecting 11. To start over, I need to set the Gateway to factory default12. I need to upgrade the firmware 13. The firmware upgrade failed, and/or the Power LED is flashing16. The Power LED flashes continuously Does the Gateway support IPX or AppleTalk? Frequently Asked QuestionsWhere is the Gateway installed on the network? Is IPSec Passthrough supported by the Gateway?How do I get Half-Life Team Fortress to work with the Gateway? What is Network Address Translation and what is it used for?Windows 2000, or Windows XP? Does the Gateway support ICQ send file?Will the Gateway function in a Macintosh environment? If all else fails in the installation, what can I do?How will I be notified of new Gateway firmware upgrades? What is DMZ Hosting?How do I reset the Gateway? What are the advanced features of the Gateway?What is the maximum number of VPN sessions allowed by the Gateway? What is a MAC Address?Windows 98 or Me Instructions Windows 2000 or XP Instructions Appendix C Upgrading Firmware Appendix D Glossary Domain - A specific name for a network of computers Packet - A unit of data sent over a network Router - A networking device that connects multiple networks together Topology - The physical layout of a network Appendix E Specifications Storage Temp Appendix E SpecificationsOperating Temp 0º~40ºC 32º~104ºFAppendix F Warranty Information Appendix G Regulatory Information User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment WEEE Appendix G Regulatory Information ADSL GatewayAppendix G Regulatory Information ADSL GatewayAppendix G Regulatory Information ADSL GatewayAppendix G Regulatory Information ADSL GatewayAppendix H Contact Information Appendix H Contact InformationADSL Gateway Need to contact Linksys?