ANT TV
ANT TV ANT SAT Connect/disconnect Back
Antenna cable(s) for: Antenna/cable (analogue) DVB-T
DVB-C
DVB-S
to antenna socket(s):
ANT TV
Connect antenna cable(s)
Initial installation

First installation

Automatic programming

Automatic programming of the TV set is started the first time you switch it on. Follow the menus.

9. You should receive a picture with sound with the settings previously made

(only for ASTRA 1 and HOTBIRD). Then press OK.

10. In the “Pre-programming“ menu, select the factory-set pre-programming to

programme the satellite stations quickly.

To ensure all stations that can be currently received are searched for and

OK

By pressing in one of the arrow directions, you can choose the

settings ...

... and confirm your settings by pressing OK. You then go to

saved, select “No“ at this point.

Symbol rates: The standard symbol rates 22000 and 27500 are preset.

If you would like to receive stations with different symbol rates, specify

OK

the next menu.

 

Back to the previous menu.

1. First you have to select the menu language.

2. By pressing the OK button, you can call the menu “Connect antenna cables(s)". If you want to receive digital stations via satellite, then choose “DVB-S“ - confirm using the yellow

coloured key. If you also want to

receive digital terrestrial stations (DVB-T), then select “DVB-T“. Also select “Antenna/cable (analogue)"

- this way the standard analogue stations can also be searched for and OK Proceed

saved. If you can receive digital stations from the cable network, then select “DVB-C“ using the yellow coloured key.

3.For the country-specific station sorting, enter the location.

4.If you have selected “DVB-T“, you then reach the menu “Antenna DVB-T“. If you use an active antenna, then select “yes (5V)”.

5.In the “Select satellite installation“ menu, make the selection that corresponds to your satellite antenna installation.

Note: If you have any questions on how your satellite antenna installation is configured and on the antenna settings, consult your antenna installer or your specialist dealer.

6.Select the satellite the antenna is directed at, such as ASTRA1. If you only receive one satellite ...

7.In the following menu, specify whether the station search should take place in the high and low band (“Yes“) or only in the low band (“No“).

Note: For most satellites, a station search is required in both bands.

8.For the low band and high band, the standard frequencies 9750 MHz (9.75 GHz) and 10600 MHz (10.6 GHz) are preset.

If your satellite antenna is equipped with an LNC (LNB) with a divergent oscillator frequency, specify the corresponding frequency for low and high band respectively. Note: The correct display of the received frequencies in the “TV menu – Settings – Channels – Manual adjustment“ depends upon this setting.

the corresponding values here using the numeric buttons on your remote

control.

11. Press OK to obtain an overview of the settings with which the automatic

programming is to take place.

12. Press the OK button again and the station search will start. The TV set

searches for, sorts and saves all the TV stations that can be received,

according to your settings and the antennas connected.

13. When the TV stations are saved, you will receive a corresponding message.

14. Press the OK button and the set then searches for the radio stations.

15. The TV set searches for, saves and sorts all radio stations which can be

received with your antenna system.

16. Then log on your video equipment, decoder and audio system using the

connection wizard and connect these to the TV according to the connection

diagram displayed. If you want to connect other equipment later, you can

find information as of page 30.

You can repeat the initial installation at any time, e.g. after moving house. Call the index using the INFO button (in the TV mode, if no menu is opened). Select the index item “Repeat initial installation“ (you will find this listed separately before the letter A). Press OK to start the initial installation.

Note: For DVB-T stations in UK the stations are tied to “Logical Channel Numbers” – “LCN” and sorted from 1-799. Digital stations without “LCN” are stored from 800 onwards. Analogue stations are stored from 1001.

Station sorting

Note: not with DVB-T stations in UK.

You can change the station sorting that was carried out automatically later at any time, see “TV menu – Settings – Channels – Change stations“.

11 -

Page 11
Image 11
Loewe 23332507.020 manual Automatic programming, Station sorting