First installation

Daily operation

Directing DVB-T antenna

Note: not with DVB-T stations in UK.

If you use a room antenna to receive one or more DVB-T stations that have picture and sound interference, then you should change the location of where the antenna is set up.

To help you direct your antenna or to help you determine the most suitable location to set up the antenna, your TV set has a display for the signal quality

Switching on/off

Your TV is equipped with an eco-standby power supply unit. On standby, the power consumption drops to low power. If you want to save even more electricity, switch the set off with the mains switch. However, please bear in mind that EPG data (electronic programme guide) will be lost and programmed timer recordings will not be performed by the TV.

C/N and the signal strength Level.

Consult your specialist dealer to find out which channels and frequency bands (VHF or UHF) are used to broadcast the digital TV stations in your area.

On any one channel, several digital stations are broadcast.

Select a TV channel

1.

Call the “TV menu“ via the MENU button.

 

 

2.

Use

to select “Settings“, then use

to select the menu line

 

underneath.

 

 

 

3.

Select “Channels“, then use

to select the menu line underneath.

 

 

 

 

 

 

 

 

 

 

 

 

TV menu

 

 

INFO END

 

 

 

 

Settings

 

 

 

 

 

 

Channels

 

Parental lock Timer functions Language

 

 

 

 

Manual adjustment

...

 

 

 

 

 

 

 

 

 

4.

Select “Manual adjustment“ and call the menu using OK

 

(in UK, the manual adjustment does not work with DVB-T).

Manual adjustment

 

 

 

 

 

Signal source

DVB-T

DVB-C

Antenna/cable (analogue)

Channel

E 05

 

 

Frequency

177.50 MHz

 

 

Name

Test

 

 

Bandwidth

7 MHz

 

 

C/N 96

 

 

Level 99

 

 

 

 

 

 

 

 

 

 

 

 

END

5.

For digital stations, select “Signal source – DVB-T“.

6.

Use the numerical buttons to specify the corresponding channel number.

 

Depending on the channel selected and country, the system automatically

 

sets the corresponding bandwidth of 7 or 8 MHz. You should only change

 

the bandwidth under special circumstances - if the channel raster in your

)

)

OK

RADIO

Switching off

If the TV set is switched on, you can switch it to standby using the blue ON/OFF button on the remote control or by using the indicator field on the set. The red lamp on the TV set lights up. If the orange indicator lights up, a timer recording is being made, EPG data is being captured or radio operation without screen display is active.

Switching on the TV set

From standby, it is best to switch the set back on using the blue On/Off button or by using the numeric buttons of the remote control (1 – 99).

Or use the switch integrated in the indicator on the set. The green indicator on the TV set lights up.

Or switch on the TV set with OK, you can then see the station list and select a station.

Switch on the radio

With the RADIO button on the remote control or:

Switch on radio using R on the control ring of the TV set.

area is different from the standard.

When you receive a digital station, the system displays the signal quality

C/N via a bar/numeric value and the signal strength via Level. The

antenna‘s direction or position is best when the largest values possible are

displayed (long bar) for the signal quality and signal strength.

7. Direct the antenna so that the largest numerical value/bar size is reached.

8. If no signal is found in the channel set, you can start the frequency search

run by pressing the blue button within the band selected (VHF or UHF).

9. Check the other channels one after another on which digital stations are

broadcast terrestrially in your area.

For the weakest station, direct the antenna so that the maximum numerical

value/bar size is achieved.

10. After you position or direct the antenna, we recommend to search for all the

stations using the “Search wizard“

(TV menu – Settings – Channels – Search wizard).

)

If you switch off the TV set using the mains switch on the set, the indicator no longer lights up.

If the TV set is switched off via the mains switch, you have to switch it into the standby mode first via the mains switch and then switch it on using one of the above mentioned methods.

- 12

Page 12
Image 12
Loewe 23332507.020 First installation Daily operation, Directing DVB-T antenna, Switching on/off, Select a TV channel