PPM1012
PPM1012 Features
2 | 3 |
| 3 | 2 X 800W PROFESSIONAL POWERED MIXER |
|
POWER | SPEAKER OUT |
| SPEAKER OUT |
| |
A |
|
| B |
| |
|
|
|
| ||
|
|
|
| THIS DEVICE COMPLIES WITH PART 15 OF THE |
|
|
|
|
| FCC RULES AND THE |
|
|
|
|
| OPERATION IS SUBJECT TO THE FOLLOWING | AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR |
|
|
|
| TWO CONDITIONS: (1) THIS DEVICE MAY NOT | WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC |
|
|
|
| CAUSE HARMFUL INTERFERENCE, AND (2) THIS | |
|
|
|
| DEVICE MUST ACCEPT ANY INTERFERENCE | SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR |
|
|
|
| RECEIVED, INCLUDING INTERFERENCE THAT | MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE |
|
|
|
| MAY CAUSE UNDESIRED OPERATION. | PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. |
| PIN | PIN |
|
| SERIAL NUMBER |
|
|
|
| ||
| 1+ | 1+ |
|
|
|
| 1 | 1 |
| CAUTION |
|
1 |
|
|
|
| |
|
|
| HOT SURFACE, |
| |
|
|
| AVOID CONTACT | REVISION | |
|
|
| OUTPUT POWER: @ 4 OHMS, |
| |
|
|
| 800 WATTS PEAK PER CH |
| |
|
|
| MINIMUM LOAD: 4 OHMS PER CHANNEL |
| |
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA • MANUFACTURED IN CHINA • FABRIQUE EN CHINE • COPYRIGHT ©2008 |
| ||||
| "MACKIE" AND THE RUNNING MAN FIGURE ARE TRADEMARKS OF LOUD TECHNOLOGIES, INC. • PATENT PENDING. |
| |||
| 4 |
|
| 4 |
|
Rear Panel |
|
|
| convenience: Speakons and 1/4" TS. | |
|
|
|
| Two common types of connector are provided for your | |
1. POWER CONNECTION |
|
|
| • Speakon outputs are wired Pin 1+ positive | |
|
|
| (hot) and Pin 1– negative (cold). | ||
This jack accepts the supplied |
|
| |||
|
|
|
| ||
cord. |
|
|
| 1– |
|
Before you plug the AC power cord into the |
|
| 1+ |
| |
|
|
|
|
| |
powered mixer, make sure that the voltage of |
|
|
|
| |
your unit is the same voltage as your local AC |
|
| COLD | 1– | |
|
|
| |||
mains supply. Use only the power cord supplied. Also, |
|
|
| 1+ | |
|
| HOT | 2+ | ||
disconnecting the plug’s ground pin is dangerous. Please |
| 2– | |||
Mono Speakon Connection |
| ||||
don’t do it. And no running with scissors either. Let's be |
|
| |||
safe out there! |
|
|
| • 1/4" TS outputs are wired Tip positive, and | |
|
|
|
| ||
2. POWER SWITCH |
|
|
| Sleeve negative. |
|
|
|
| SLEEVE | SLEEVE TIP | |
|
|
|
| ||
Press the top of this rocker switch inwards to turn on |
|
the mixer. The front panel power LED [42] will glow | TIP |
| |
with happiness, or at least it will if you have the mixer | TIP |
| |
plugged into a suitable live AC mains supply. | SLEEVE |
Press the bottom of this switch to turn off the mixer, whenever you feel that this would be a safe thing to do.
As a general guide, you should turn on your
powered mixer first, before any external power
amplifiers or powered speakers, and turn it off last. This will reduce the possibilities of any
3. SPEAKER-LEVEL OUTPUTS
These output connections provide
The power output of the PPM1012 is 500 watts rms per channel into 4 ohms, and 800 watts peak.
1/4" TS Connection
These two types of outputs are wired in parallel, and it is possible to use both types at once.
The minimum impedance that the powered
mixer can handle is 4 ohms per channel, and we recommend that you do not go below this.
If you are using both outputs per channel, make sure each loudspeaker is 8 ohms impedance or greater.
4. VENTILATION
These holes in the rear panel allow the inter-
nal fans to flow breezy and 
air over the internal power amplifiers. Do not obstruct these holes, or the amplifiers may overheat and
shut down. Do not remove the feet, as these help keep the powered mixer off the ground for ventilation.
10 
PPM1012
