Magnavox 15MF Series owner manual Lcd Tv

ANTENNA CONNECTION

CABLE BOX CONNECTIONS

Acombination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69).

Your connection is easy because there is only one 75 Ω(ohm) antenna jack on the back of your TV, and that’s where the antenna goes.

1	If your antenna has a round cable
	(75 ohm) on the end, then you’re ready to
	connect it to the LCD TV. If your
	antenna has flat, twin-lead wire (300 ohm), you
	first need to attach the

Outdoor or Indoor Antenna (Combination VHF/UHF)

Rear Jack panel of

� Television

If you have a Cable Box, follow either set of these steps to complete your

connections.

Cable Box with RF In/Out Jacks

This connection will not supply Stereo sound to the LCD TV.

1	Connect the Cable TV signal to the IN jack (or
	RF IN or CABLE IN) on the Cable Box.
	Connect an RF coaxial cable (not supplied) to
2 the OUT jack (or TO TV or RF OUT) of the
	Cable Box.

The Cable TV signal from

the Cable Company			�
�	�
		OUTPUT
			CH
CABLE	TO TV	3	4

IN

75 �

� Coaxial Cable

L-Adapter

antenna wires to the screws on a 300- to

75-ohm adapter(not supplied).

Connect the antenna (or adapter) to one end

2 of the supplied L-Adapter as shown, and con-

Twin-lead wire to 300-75�adapter

�

Connect the other end of the coaxial cable to

3 one end of the supplied L-Adapter as shown,

and connect the other end of the adapter to

the TV jack on the LCD TV.

Side Jack Panel of

Television

VGA

nect the other end of the

L-Adapter to the TV jack on the side of

the LCD TV.

OR

Antenna with 75 �

cable L-Adapter

Plug the DC adapter into the DC IN 16V	�
4 jack on the LCD TV. Plug the power cable into

an outlet.

5Set the Channel 3/4 (or Output channel) switch of the Cable Box to 3 or 4. Set the TV to the same channel. When watching TV programming, change channels at the Cable Box, not the LCD TV.

DC Adapter

Power

Cable

PC

BASIC CABLE TV CONNECTION

Your Cable TV signal into your home may be a single, 75Ω(ohm) cable. If so, this connection is

very simple. Follow the step below to connect your Cable TV signal to your new LCD TV.

1 Connect the Cable TV signal to one end of the supplied L-Adapter as shown, and connect the other end of the adapter to the TV jack on the

LCD TV.

Rear Jack panel of

Television

8

The Cable TV signal from Cable Company

(75 � coaxial cable)

�

L-Adapter

Cable Box with Audio/Video Out Jacks This connection will supply Stereo sound to the LCD TV.

1Connect the Cable TV signal to the

IN jack (or RF IN or CABLE IN) on the Cable

Box.
Using an RCA-type video cable (not
2 supplied) connect one end of the video cable to
the Video Out jack of the Cable Box.Connect
the other end of the cable to the yellow VIDEO
jack on the side of the TV.Video cables are
usually marked with yellow and are available
from Magnavox or electronics retailers. Video
jacks on most equipment are yellow.	�		VGA
			PC
Using RCA-type, stereo audio cables (not
3 supplied), connect one end of the cables to the
left and right Audio Out jacks of the Cable Box.		DC Adapter
Connect the other end of that cable to the
Audio jack on the side of the LCD TV.Audio		Power
cables are usually marked with red and white		Cable	Cable
and are available from Magnavox or electronics			TV signal
retailers.The right
audio jack is red and the left audio jack is white.		�
Match the cable colors to the jack colors.
			CABLE	TO
Plug the DC adapter into the DC IN 16V			IN	TV
4 jack on the LCD TV. Plug the power cable into

an outlet.

9

S - VIDEO

AUDIO

VIDEO

Side Jack Panel

of Television

�

Video Cable

�

Audio Cable

OUTPUT

CH

34

L AUDIO R	VIDEO
OUT	OUT

Cable Box