Magnavox VRT642 owner manual Timer Recording With VCR Plus, Enter, Number-Button Buttons OButton

27

Timer Recording With VCR Plus-"

oeeeoe eoeoll oeoooe eooee oeoo eeee •ioel• Io• eee eeooe*ol•eoloeleoeee• • • • •

Remote Control

POWER

Button

PLUS+/

ENTER

Number-Button

Buttons

OButton

Read steps 1-7 to program a timer recording using VCR Plus+ numbers. Before you begin make sure:

•Channels have been programmed.

•The clock has been set.

•There is a tape in the VCR (make sure the tape's record tab is intact and the tape is long enough to record the program(s).

•The VCR is in VCR position.

•You have selected CABLE TV or TV at the TUNER SET UP menu.

4

Press the Number 1 button to record in

SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP

speed. For details, see page five. You cannot use the (Tape) SPEED button at this time.

_'_

MEON 10:30 PM

EOFF 1'_:30PU

Button

00000

750oo

You must do each step within 60 sec- onds of completing the previous step. If you don't, you will have to start again at step 1.

1

Press the VCR PLUS+/ENTER button on the remote control. The on-screen display shown below will appear.

ti_n _b_'l_" "_E_

END _ MENU

5

Press the MENU button. PROGRAM WAS COMPLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen. After three seconds, the on-screen display - will disappear.

PwsCOOE_';-_:-

•If CODE ERROR appears at step 2

after you		enter		the		VCR Plus+				number,	_RPLu_PRO_.1
the	number		you		entered		was		incorrect		X_. END PUSH MENU
(for example, too short). If this hap-											2
pens, press the CLEAR button to clear
the	number,		then		enter		the	correct
number.											Press the Number buttons for the VCR
• CLASH		m_yflash			on the			screen		at step	Plus+ number of the program you wish
2.	This	means		that		the	timer		recording		to record (this number is different for
you	just	programmed				and		another			every program, and it can be four to
tim,er recording					overlap,		and		thus the		eight digits long). Finally, press the
current		timer		recording			will		not	be	VCR PLUS+/ENTER button.
carried		out.

•To quit VCR Plus+ programming at

any step, press the MENU button. The

PkUSCODE: I_-..--

on-screen display will disappear from

_oRP,0_P_O_. 1

the TV

screen.

TO SET PUSH VCR +

•

If the

preset

time

for

a timer

recording

• TO CORRECT PUSH CLEAR

END PUSH MENU

comes up during an OTR, the OTR has

3

priority.

•

To stop

a started

timer

recording,

press

the STOP/EJECT

button

on the

VCR.

To record the program once, press the

•

If the

power

fails

for

more

than

one

Number

1 button to select ONCE. To

minute,

programmed

timer

recordings

• record the same program every day from

may

be

lost.

If

this case,

repeat the

Monday

through Friday, press the

steps

on pages

seven

and

ten

before re-

Number

2 button to select DAILY. To

programming

the

timer

recordings.

record the same program every week on

the same day (such as every Saturday),

See page 37for more notes. press the Number 3 button to select

6

If needed, press the VCR PLUS+/ENTER button and repeat steps 2 to 5. When you are finished, go to step 7.

7

Turn off the VCR power. The Timer light will appear. The VCR must be turned off for a timer recording to take place. If you forget to turn the VCR off, PLEASE TURN OFF VCR FOR TIMER RECORDING flashes on your TV screen two minutes before a timer recording starts. You can remove it by pressing the CLEAR but- ton.

The VCR 1 must be off for a

timer recording to take place!

W'I_F,KT