Makita DPC 9500, DPC 7000, DPC 9501 Fuels/ Refuelling@, Gasoline I 50l 25l, Correct mixture ratio

NOTE: Tighten the Allen screw tightly. If this is not done, the cutting disc can slip during cutting.

Fuels/ Refuelling@

Gasoline I 50:l 25:l

other oil

1.O Us-gal. (3.7 I) 2.5 floz. (75 cm3) 5.0 floz. (150 cm3)

2.5Us-gal. (9.4 I) 6.4 floz. (189 cm3) 2.8 floz. (378 cm3)

A 5.0 Us-gaL(18.9 I) 12.8 floz. (378 cm3) 5.6 floz. (756 cm3)

Fuelmixture

The Power Cut is powered by a high-performance two-stroke engine. It runs on a mixture of gasoline and two-stroke engine oil.

The engine is designedfor unleaded regular gasolinewith amin. octane value of 91 ROZ. In case no such fuel is available, you can use fuel with a higher octane value. This will not affect the engine.

In order to obtain an optimum engine output and to protect your health and the environment use unleaded fuel only. Gasolinewhich contensalcoholshouldnot usedin MAKITA products.

For lubricating the engine use a two-stroke engine oil (quality grade: TC-3),which is added to the fuel. The engine has been designed for use of MAKITA high-performance two-stroke en- gine oil and a mixture ratio of only 50:l to protect the environ- ment. In addition, a long service life and reliable operation with a minimum emission of exhaust gases are ensured.

MAKITA high-performance two-stroke engine oil is available in the following sizes to suit your individual requirements:

1I order number 980 008 607 100 ml order number 980 008 606

In case MAKITA high-performance two-stroke engine oil is not available, it is urgently recommended to use a mixture ratio of 25:1, as otherwise optimum operation of the engine cannot be guaranteed.

-Fit the pressure disc (M/16) on the shaft, observing the flattened side of the shaft.

NOTE: The arbor hole of the pressure disc is shaped to fit the shaft. When puttingthe pressurediscon the shaft, turn itslightly until it fits.

-Screw in the Allen screw (M/15) by turning it to the left (counter-clockwise - left-hand thread!) and tighten by hand.

-Slowly turn the cutting disc until the stop hole of the V-belt wheel is visible in the drive-arm hole (M/18).

-Push the assembly tool (M/19) allthe way into the stop hole of the V-belt wheel. The shaft is now blocked.

-Tighten the Allen screw with the Allen key (M/20).

The correct mixture ratio:

50:l when using MAKITA high-performancetwo-stroke engi- ne oil, i. e. mix 50 parts gasoline with 1 part oil.

2 5 1 when usingothertwo-strokeengineoils, i. e. mix25parts gasoline with 1 part oil.

NOTE:

For preparing the fuel-oil mixture first mix the entire oil quantity with half of the fuel required, then add the remaining fuel. Thoroughly shake the mixture before filling it into the Power Cut tank.

It is notwise to add more engine oil than specified to ensure safe operation. This will only result in a higher production of combus- tion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the muffler. In addition, fuel consumption will rise and performance will de- crease.

Fuelstorage

Fuels haveonlyalimitedshelf-life.Buyonlyas muchasyou will use in 4 weeks.

Store fuel only in approved and marked containers.

AVOID SKIN AND EYE CONTACT

A

Mineral oil products degrease your skin. If your skin comes in contact with these substances repeatedly and for an extended period of time, it will desiccate. Various skin deseases may result. In addition, allergic reactions are known to occur.

Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

14