ENGLISH
OTHER OPERATION
7Confirm and change timer program
•You can check and change the timer program setting as follows.
1.Press the TIMER button x.
2.Either turn the Easy JOG 4/¢ knob !5or press the 5 or ∞ button c to select timer program number.
3.You can change the displayed contents with the Easy JOG 4/¢ knob !5or 5 or ∞ button c and ENTER buttons b if necessary.
Note
•Timer program is not changed if you quit confirming halfway through a procedure.
7Timer program off
1.Press the TIMER button x, “TIMER PROGRAM 1” is displayed.
2.Either turn the Easy JOG 4/¢ knob !5or press the 5 or ∞ button c to select timer program number.
3.Press the Easy JOG 4/¢ knob !5or ENTER button b, “TIMER PROGRAM x SET” is displayed.
4.Either turn the Easy JOG 4/¢ knob !5or press the 5 or ∞ button c to select “TIMER PROGRAM x OFF”.
7Sleep timer
•The sleep timer function allows the unit to be in standby mode automatically after specific period of time.
1.Press the SLEEP button ⁄7on the remote control.
2.Each press of the button will increase the time before shut down in the following sequence.
OFF
10 
20 
30 
60 
90 
120 
3.The sleep timer will be shown for 5 seconds in the display, and it will count down until the time has elapsed. When the programed sleep timer has elapsed, the unit will automatically turn off.
Note that the display will be dimmed when the sleep timer is programed.
4.Press the SLEEP button ⁄7. The display shows the remaining time until standby mode begins.
5.To cancel the sleep timer, press the SLEEP button ⁄7repeatedly until the display shows “SLEEP OFF”.
•When the sleep timer is programed, DIMMER function does not activate.
LAST FUNCTION MEMORY
•This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off.
This function eliminates the need to perform complicated resettings when the power is turned on.
•The unit is also equipped with a
This function provides approximately one week of memory storage when the main unit’s power switch is off and with the mains cord disconnected.
INITIALIZATION OF THE MICROPROCESSOR
•When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the microprocessor is required by the following procedure.
1.Unplug the mains cord from the power outlet after pressing the POWER ON/STANDBY
switch q or 
button z and setting the standby mode.
2.Holding both the MENU button u and POWER ON/STANDBY switch q, plug the mains cord into the power outlet.
3.Check that the entire display is flashing with an interval of about 1 second, and release your fingers from the 2 buttons and the microprocessor will be initialized.
!5u
CD RECEIVER CR601
| INPUT | MENU | DIRECT |
BASS | TREBLE |
|
|
PUSH TO ENTER |
| VOLUME |
|
| STANDBY |
|
|
| POWER ON / STANDBY |
| PHONES |
q |
|
|
| CLOCK | |
|
|
| CALL | |
z |
|
|
| |
TIMER | 1 | 2 |
| |
x | 3 | |||
|
| |||
| 4 | 5 | 6 | |
|
|
| ||
c | 7 | 8 | 9 | |
|
| |||
|
|
| ||
ENTER |
| 10/0 | CLEAR | |
b |
|
| ||
|
|
| ||
MENU |
|
| DISPLAY | |
n |
| VOL |
| |
| INPUT | MUTE | INPUT | |
MODE |
|
| REPEAT | |
|
| VOL |
| |
TUNING | PRESET | |||
DIMM | DAB | FM | AM | |
AUTO TUNE SLEEP | SHIFT | DIRECT | ||
MEMO |
|
|
| |
⁄7 | REMOTE CONTROLLER | |||
| RC601CR |
| ||
5.Press the Easy JOG 4/¢ knob !5or ENTER button b to turn off the timer program.
Note
•To turn a timer program back on again, repeat this procedure and select “TIMER PROGRAM x ON”.
Notes
•If step 3 does not work,start over from step 1.
•If the microprocessor has been initialized all the button settings are reset to the default values (the values set upon shipment from the factory).
26
