ENGLISH | ADVANCED CONNECTING |
|
CONNECTING THE REMOTE CONTROL JACKS
|
|
| VIDEO |
|
|
|
|
|
|
|
|
| S |
|
|
|
|
|
|
|
|
|
|
|
|
| V |
FM (75Ω) | GND AM |
|
| IN | OUT | IN | OUT |
|
| MONITOR | IN VCR1OUT | DVD MONITOR | |
ANTENNA |
|
| DSS / VCR2 |
| VCR1 | DVD | TV | L | SL | C | SBL | ||
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
IN | OUT | IN | OUT | IN | OUT | IN | OUT |
|
| R | SR | SW | SBR |
CD | TAPE | CDR/MD | DSS / VCR2 |
| VCR1 | DVD | TV |
| 7.1CH INPUT |
| |||
|
|
|
|
|
| AUDIO |
|
|
|
|
|
| |
|
|
|
|
|
| ||
|
|
|
|
| S- |
|
|
|
|
|
|
| VIDEO |
|
|
|
| IN VCR1OUT |
|
|
| Y | |
TV | MONITOR | DVD MONITOR | IN | OUT |
| ||
L | SL | C | SBL |
|
|
| |
|
|
|
|
|
|
| CB/PB |
|
|
|
|
|
|
| CR/PR |
| R | SR | SW | SBR | 1 | 2 | 3 |
TV |
| 7.1CH INPUT |
|
|
| DVD DSS / VCR 2 MONITOR | |
|
|
|
|
| DIGITAL INPUT | COMPONENT VIDEO | |
2
RC OUT
OPTION
MODEL NO. SR
| R | L | R | L | R | L |
|
|
| FRONT | SURROUND BACK | SURROUND | CENTER | ||
SUBWOOFER |
|
| S. SPEAKER B |
|
|
| |
OUT | SPEAKER SYSTEMS 6 - 8 OHMS |
|
|
|
| ||
L R L R 
R L
L R L R 
L R
R | L | R | L |
|
RROUND BACK | SURROUND | CENTER | ||
. SPEAKER B |
|
|
| |
8 OHMS
1
CONTROL | CD recorder | CONTROL | MD deck | CONTROL | CD player |
REMOTE |
| REMOTE |
| REMOTE |
|
IN |
| IN |
| IN |
|
OUT |
| OUT |
| OUT |
|
| EXTERNAL INTERNAL |
| EXTERNAL INTERNAL |
| EXTERNAL INTERNAL |
| CENTER |
|
L |
|
|
R |
|
|
FRONT SURR. | SUB | SURR. |
| WOOFER | BACK |
DVD Audio player
or
SACD Multi channel player
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the 7.1 channel input level menu. See page 29.
q
You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you only need to aim the remote at one unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier’s, power switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature.
w
Whenever external infrared sensors or similar devices are connected to
1. Hold down the 7.1CH INPUT button and MENU button on the front panel at the same time for five seconds.
2. The setting “IR=ENABLE” is shown on the FL DISPLAY.
3. Press the 1 or 2 cursor button to change this to “IR=DISABLE”.
4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled.
Note:
Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands.
5. To restore the original setting, perform steps 1 to 4 to set to “IR=ENABLE”.
14
