OTHER FUNCTION
ATTENUATION TO ANALOG INPUT SIGNAL
BASS TREBLE TUNE/SEARCH
SURROUND
DIGITAL
AAC
INPUT/DISC+ AUDIO
CH.SEL | LIP.SYNC |
SYSTEM REMOTE CONTROLLER
RC5500SR
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR3001’s output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.)
AV SURROUND RECEIVER SR3001
DISPLAY MODE
AV SURROUND RECEIVER SR3001
SET UP/ | MENU OFF | ||
T.TONE |
|
| |
PURE DIRECT | AUTO |
| DTS |
SURROUND | 1 | 2 | 3 |
DIGITAL | |||
AAC |
|
|
|
NIGHT | CSII | EX/ES | VIRTUAL |
| 4 | 5 | 6 |
DISPLAY | STEREO | 7.1CH IN | |
| 7 | 8 | 9 |
CLEAR | MEMO | A/D | |
|
| 0 |
|
|
| CHANNEL/SKIP | |
BASS | TREBLE | TUNE/SEARCH | |
| RDS | F.DIRECT | |
You can select the display mode for the front display of the SR3001.
To select this mode, press the DISPLAY on the front panel or on the remote.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
SET UP/ | MENU OFF |
| |
T.TONE |
|
| |
PURE DIRECT | AUTO |
| DTS |
| 1 | 2 | 3 |
NIGHT | CSII | EX/ES | VIRTUAL |
| 4 | 5 | 6 |
DISPLAY | STEREO | 7.1CH IN | |
7 8 9
CLEAR MEMO A/D
0
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH
If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source with the A/D button on the remote
ENGLISH
If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote.
“ATT” indicator will be illuminated when this function is activated. The
This function is memorized for each individual input source.
Notes:
•When using headphones, the surround mode will change to STEREO and TruSurround (TS) headphones by SURROUND MODE button.
•The surround mode returns to the previous setting as soon as the plug is removed from the jack.
VIDEO ON/OFF
When no video signal is connected to the SR3001 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.
To select video off, press the
T.TONE |
|
| |
PURE DIRECT | AUTO |
| DTS |
| 1 | 2 | 3 |
NIGHT | CSII | EX/ES | VIRTUAL |
| 4 | 5 | 6 |
DISPLAY | STEREO | 7.1CH IN | |
| 7 | 8 | 9 |
CLEAR MEMO A/D
|
| 0 |
|
|
| CHANNEL/SKIP | |
BASS | TREBLE | TUNE/SEARCH | |
| RDS | F.DIRECT | |
INPUT/DISC+ | AUDIO | PTY | |
CH.SEL |
|
| LIP.SYNC |
When this button is pressed, the display mode is switched in the following sequence.
→Surround Mode →
→Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the front display, in display off condition
controller.
When this button is pressed, the input mode is switched in the following sequence.
→Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.
If no digital signal is being input, the analog input jacks are selected automatically.
In Digital mode, input is fixed to an assigned digital input terminal.
In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory.
If you need to change the input mode completely, use INPUT setup in SETUP MENU system. (see page 17)
27
