Other Functions, English, Multi Room Selector Operation

OTHER FUNCTIONS

MULTI ROOM SELECTOR

The Multi Room Selector is a function which allows you to listen to the same or a different source in a room other than the room in which the SR-19EX is located. To use this function, a multi room remote unit and remote control signal receiver available from your Marantz dealer are necessary. The operations possible with the multi room function are explained briefly below. For details, refer to the instruction manual supplied with the multi room remote control unit and receiver.

MULTI ROOM SELECTOR OPERATION

1.Press the MULTI button !9. The unit enters multi room mode and the display indicates “SELCT SOURCE” and flashes the “MULTI” indicator for approx. 10 seconds. In this time, you can select the input source by turning the INPUT SELECTOR knob !5.

2.Then, the display indicates “MULTI VOL” “VOLUME xx dB” for approx. 5 seconds. During this time, you can set the volume level for the multi room operation. This will only set the volume in the second room.

MULTI ROOM SELECTOR OPERATION (USING THE MULTI ROOM REMOTE CONTROL UNIT)

1.Press the MULTI button, the POWER ON button, or select the desired source on multi room remote control unit from the MULTI ROOM. Any of these operations will put the SR-19EX into multi room mode and “MULTI” will light in the display.

2.Press the VOLUME + or VOLUME – button on the multi room remote control unit to set the desired sound volume.

3.In multi room mode, the multi room remote control unit can be used in the multi room to operate the following functions.

You can select a tuner preset channel and tuning up or down, and direct frequency selection. And you can control the CD player LD player, DVD player and other source connected to the SR-19EX.

Caution:

•Multi room mode can only be selected when the SR-19EX POWER switch q is turned on.

•If the main room is active (not standby mode), you cannot select a radio band except the band of the main room. For example; if the FM band is selected in the main room, you cannot select the AM band in the multi room.

•The operating procedure for this is the same as the Multi-room operations using the remote unit.

•If you operate from second room, SR-19EX will output video signal with OSD information.

M U L T I R O O M S E T U P

V I D E O		:	D V D
A U D I O		:	D V D
V O L U M E L E V E L		:	– 7 5 d B
		: V A R I A B L E
S L E E P T I M E R		:	9 0 m i n
– – – M A I N – R OO M S T A T U S – – –
V I D E O	:	L D
A U D I O	:	L D

DIALOGUE NORMALIZATION MESSAGE

Dialogue Normalization (Dial Norm) is a feature of Dolby Digital. When playing back software which has been encoded in Dolby Digital, sometimes you may see a brief message in the front panel display which will read “Dial Norm X dB” (X being a numeric value). Dialogue Normalization serves to let you know if the source material has been recorded at a higher or lower level than usual. For example, if you see the following message: “Dial Norm + 4 dB” in the front panel display, to keep the overall output level constant just turn down the volume control by 4 dB. In other words, the source material that you are listening to has been recorded 4 dB louder than usual.

If you do not see a message or see “Dial Norm 0 dB” in the front panel display, then no adjustment of the volume control is necessary.

TV AUTO ON/OFF FUNCTION		ENGLISH
This function allows the component connected to the TV IN jack to		ENGLISH

control the power (ON/OFF) to the SR-19EX.
AUTO POWER ON
1.	Be sure TV auto mode is on. (Refer page 18 : System Setup 1/2 )
2.	Connect your TV TUNER (etc) to the TV IN terminal.
	Be sure to connect the video input.
3.	Turn OFF the power to the TV TUNER and the SR-19EX.
3.	Turn OFF the power to the TV TUNER and the SR-19EX.
4.	Turn ON the TV TUNER and tune in a receivable station.
5.	When the station is received, the SR-19EX turns ON and TV is
	selected automatically.