OTHER FUNCTION
ATTENUATION TO ANALOG INPUT SIGNAL
DVD | MD |
|
| MODE | PTY |
VCR1 | TAPE |
|
VCR2 | DISP./RDS | P.SCAN |
DSS | CD |
|
ATT.
TUNER AMP
SYSTEM REMOTE CONTROLLER RC4300SR
When the input signal is too high and the voice distorts even by throttling the SR4300 VOLUME control, turn on this function. “ATT” is indicated when this function is activated.
“ATT” indicator will light up when this function is activated. The signal- input level is reduced by about the half. Attenuation will not work with the output signal of
This function is memorized for each individual input source.
LISTENING OVER HEADPHONES
This jack may be used to listen to the SR4300’s output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phone plug. (Note that the main room speakers will automatically be turned off when the headphone jack is in use.)
Notes:
•When using headphones, the surround mode will automatically change to STEREO.
•The surround mode returns to the previous setting as soon as the plug is removed from the jack.
DIMMER
AV SURROUND RECEIVER SR4300
SURROUND
You can change the display brightness of the front display.
Press the DIMMER button on the front panel to change the brightness. When this button is pressed, the brightness is changed in the following sequence.
→dimmed → Display Off → normal → dimmed ....
Note:
•Only DISP indicator will light up on the front display in display off condition
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
|
| AUTO |
| DTS |
| AV SURROUND RECEIVER SR4300 | 1 | 2 | 3 |
SURROUND | TREBLE | CS | EX/ES | DSP |
| ||||
|
| 4 | 5 | 6 |
|
| 2CH | 6.1CH | |
|
| ST |
| |
|
| 7 | 8 | 9 |
| BASS | F.DIRECT | A/D |
|
|
|
| 0 |
|
|
|
|
| OFF |
| SETUP/T.TONE |
|
| MENU |
OK
If you have already assign any digital input to input source.
You can select temporarily the audio input mode for each input source with the A/D button on the remote controller or front panel.
When this button is pressed, the input mode is switched in the following sequence.
→Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.
If no digital signal is being input, the analog input jacks are selected automatically.
In Digital mode, input is fixed to an assigned digital input terminal. In analog mode, the analog input jacks are selected.
This selecting is temporarily, so the result will not be stored in memory. If you need to change input mode completely, use SYSTEM SETUP in SETUP menu system. (see page 19)
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source selected for listening through the SR4300 is sent to the record outputs.
This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT ,
To record the input source signal you are currently watching or listening to
1. |
|
|
|
|
| NIGHT |
|
AV SURROUND RECEIVER SR4300 |
| CHANNEL/SKIP | |
SURROUND | TV | CDR |
|
|
| ||
|
| TUNE/SEARCH | |
| DVD | MD |
|
1. |
| MODE | PTY |
VCR1 | TAPE |
| |
VCR2 | DISP./RDS | P.SCAN | |
| DSS | CD |
|
|
|
| ATT. |
| TUNER | AMP |
|
| SYSTEM REMOTE CONTROLLER RC4300SR | ||
1. Select the input source to record by pressing the corresponding
input selector button.
The input source is now selected and you may watch or listen to it
as desired.
2. Outputs the currently selected input source signal to the TAPE
OUT ,
for recording.
3. Start recording at the recording component as desired.
Notes:
•If you change the input source during recording, you will record the signals from the newly selected input source.
•You cannot record the surround effects.
•Digital input signals are only output to the digital outputs. There is no conversion from digital to analog .
When connecting CD players and other digital components, do not connect only the digital terminals, but the analog ones as well.
ENGLISH
31
