Marantz SR6001 manual Rear Panel, e r t y, 7!6!5!4, 3 !2!1!0 o

ENGLISH	REAR PANEL
	q w	e r t y	u

			INPUT 1(TV)	INPUT 2(DVD)
						SURROUND	SPEAKER
				OUTPUT	MODEL NO. SR6001	BACK	SYSTEMS
						L	L
FM (75)	GND	AM	ANTENNA				FRONT
							A

COMPONENT

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

Y

CB/PB

CR/PR

@1

VIDEO

INPUT 3(VCR)

INPUT 4(DSS)

RS-232C

R

R

INPUT 1(DVD)

INPUT 2(DSS)

OUTPUT

/ SPEAKER C

HDMI

MULTI SPEAKER

Ver1.2

AC IN

L

TV(1)

DVD(2)

VCR(3)

DSS(4)

MONITOR

TV(1)

DVD(2)

VCR(3)

DSS(4)

MONI. OUT

FRONT

IN

OUT

OUT

@0 VIDEO

B

R

IN

OUT

S-VIDEO

DIGITAL IN

DIGITAL OUT

RC-5 MULTI RC

DC OUT

L

SL

SBL

C

ON

!9

4

5

COAX.

IN

OFF

CEN

1

2

3

OPT.

TER

FLASHER

PRE

IN

OUT

OUT

L

R

SR

SBR

SW

TV

DVD

VCR

DSS

TAPE

CD/CD-R

MULTI

L

SL

SBL

C

SURR

OUND

!8

L

R

7.1CH

R

IN

AC OUTLET

FRONT A OR B.CENTER.SURR.

SURR BACK : 6 - 8 OHMS

IN

OUT

IN

OUT

IN

OUT

OUT

R

SR

SBR

SW

230V 50/60Hz

FRONT A + B : 8 OHMS

AUDIO

(AUX2)

SWITCHED

0.65A 150W

!7!6!5!4

!3 !2!1!0 o

i

ySpeaker outputs terminals

(SURROUND BACK / MULTI

SPEAKER / SPEAKER C)

Two terminals are provided for the front left, and right speakers for multi room (2nd zone) or surround back.

The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 23.

uSpeaker outputs terminals

Seven terminals are provided for the front (A) left, front (A) right, front (B) left, front (B) right, front center, surround left, and surround right speakers.

iSPEAKER C switch

Set to ON to connect a bi-amp to this receiver or set to OFF for normal speaker connection (surround back and multiroom speakers). (See page 23)

oAC OUTLETS

Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED terminal is provided.

!2Subwoofer Output

Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifi er input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier.

!37.1 CHANNEL or AUX2 INPUT

By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs.

!4FLASHER IN (Flasher input terminal)

These terminals are to control the unit from each zone. Connect the control signal from a Keypad, etc.

!5DC TRIGGER output terminal

Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system OSD setup menu to determine the conditions by which these jack will be active.

qFM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.

wCOMPONENT VIDEO INPUT/

OUTPUT

If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR6001. The SR6001 has 4 component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component, and 1 component video output connector to output the information directly into the matrix decoder of the display device.

By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail.

eMultiroom Output (Audio output)

This is the audio output jack for the Multi zone (Multi room).

Connect these jacks to optional audio power amplifiers to listen the source selected by the multiroom system in a remote room.

rMONITOR OUT

These are monitor outputs and each one includes both composite video and S-video confi gurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections.

tRS-232C

The RS-232C port is to be used in conjunction with an external controller to control the operation of the SR6001 by using an external device.

The RS-232C port may also be used in the future to update the operating software of the SR6001 so that it will be able to support new digital audio formats and the like as they are introduced.

The one marked SWITCHED provides power only when the SR6001 is turned on and is useful for components which you use every time you play your system.

Caution:

•In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR6001 is turned on.

•The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.

!0AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

SR6001 can be powered by 230V AC only.

!1Preamp Outputs

(L, R, SL, SR, SBL, SBR, C)

Jacks for L (front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right).

Use these jacks for connection to external power amplifiers.

Note:

•This output voltage is for (status) control only, It is not sufficient for drive capability.

!6MULTI ROOM REMOTE IN/OUT terminals

IN: Connect to a multi-room remote control device, available from your Marantz dealer.

OUT: Connect to the Marantz component equipped with remote control (RC-5) terminals in Multi zone (Multi room).

!7REMOTE CONT. IN/OUT terminals

Connect to a Marantz component equipped with remote control (RC-5) terminals.

!8AUDIO IN/OUT (TV, DVD, VCR, DSS, TAPE, CD/CDR)

These are the analog audio inputs and outputs. There are 6 audio inputs and 3 audio outputs. The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc....

The audio inputs and outputs require RCA-type connectors.

8