Marantz SR6001 manual Speaker A/B

DISPLAY MODE

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source

SPEAKER A/B

ENGLISH

AV SURROUND RECEIVER SR6001

SURROUND

DIGITAL

AAC

LEARNSEND

SOURCE	SET	OFF	ON
l/
SLEEP	DISPLAY	P.DIRECT	SURROUND
			LIP SYNC/
AUTO	2	dts	INPUT
1		3	BAND
CS	EX/ES	VIRTUAL	T.MODE
4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9

TV DVD VCR DSS

TUNER CD CDR MD

TAPE AUX1 AUX2 AMP

REMOTE CONTROLLER

RC5001SR

4	5	6
M-CH ST	STEREO	NIGHT P.SCAN
7	8	9

selected for listening through the SR6001 is sent to the record outputs.

This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD/CDR OUT and VCR OUT in the record mode.

To record the input source signal you are currently watching or listening to

SURROUND

DIGITAL

AAC

M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9
	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME
	MULTI/ CAT	M-SPKR
INFO			MENU

ENTER

You can select the display mode for the front display of the SR6001.

To select this mode, press the DISPLAY on the remote control or the front panel.

When this button is pressed, the display mode is switched in the following sequence.

Input Mode → Surround Mode → Auto display OFF

→Display OFF → Normal Mode → Input Mode

Normal Mode:

Displays the selected input function. If the function has been renamed using the Function Rename feature (see page 29), the renamed name appears on the display.

Input Mode:

Displays the input mode set via the Function Input Setup feature (see page 28).

Surround Mode:

Displays the status of the selected surround mode.

Auto Display Off mode:

The display is off. But, if you make a change to the unit such as the input or surround mode, the display will show that change, then go back to off after about 3 seconds.When changing the volume, it is not displayed.

Display Off mode:

The display is off completely.

Note:

•Only the DISP indicator will be illuminated on the front display in display off condition.

	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME
	MULTI/ CAT	M-SPKR

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures.

Press the AMP button first to enter the AMP mode then press the A/D button.

When this button is pressed, the input mode is switched in the following sequence.

Auto → HDMI → Digital → Analog → Auto

Auto mode:

The types of signals being input to the digital and analog input jacks for the selected input source are detected automatically.

If no digital signal is being input, the analog input jacks are selected automatically.

HDMI mode:

HDMI mode can be selected only when an HDMI input has been assigned as an input source. When “HDMI AUDIO” under PREFERENCE of the SETUP MENU is set to “THROUGH”, the HDMI mode cannot be selected.

Digital mode:

The input signal is fixed to an assigned digital input terminal.

Analog mode:

The analog input jacks are selected.

This selection is temporary and will not be stored in memory.

To store changes to the input mode, select “1. INPUT SETUP” from the MAIN MENU. (See page 28)

1.

	- PRESET +		- TUNING +
AV SURROUND RECEIVER SR6001
	DISC+	ANGLE	SUB TITLE	AUDIO
	CH-SEL V-OFF		ATT.
1.		BASS	TREBLE
	TV	DVD	VCR	DSS
	TUNER	CD	CDR	MD
	TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

1. Select the input source to record by turning the INPUT FUNCTION SELECTOR knob on the front panel or simply press the input selector buttons on the remote.

The input source is now selected and you may watch or listen to it as desired.

2. The currently selected input source signal is output to the TAPE OUT, CD/CDR OUT and VCR OUT outputs for recording.

3. Start recording to the recording component as desired.

SR6001 has speaker system - A and speaker system- B for front L/R channels.

You can select these systems by pressing SPEAKERS A/B button on the front panel or SPKR A/B on the remote.

50