Marantz manual 1. 3, 8 7.1 CH INPUT LEVEL, Multi Plc Setup, English, Notes, <ZR6001>, <ZC4001>

ENGLISH

LEVEL (VOLUME LEVEL):

Adjust the Multi-speaker output level with or cursor button.

Note:

•This setting can be changed when the Surr Back is set “NONE” in 2-1 SPEAKER SIZE menu. When this setting is unavailable, “✽ ✽ ✽ ” is displayed

MAIN ROOM STATUS:

Selected input source in the main room will be displayed.

Note:

•If “VOLUME” is set to “FIXED”, the multi-room output level cannot be adjusted from the second zone.

After you complete this portion of the set up, move the cursor to “MAIN” with or cursor buttons and press ENTER button.

8 7.1 CH INPUT LEVEL

This sub-menu is to adjust the speaker levels for 7.1-channel input sources.

Here you will adjust the volume for each channel so that they are all heard by the listener at the same level.

	8 7 . 1 CH I N P U T L E V E L
	V I D EO I N		:	L A S T
	F RON T	L	:	0	d B
	C E N T E R		:	0	d B
	F RON T	R	:	0	d B
	S URR . R		:	0	d B
	S URR . B	R	:	0	d B
	S URR . B	L	:	0	d B
	S URR . L		:	0	d B
	S UB W		:	0	d B
	MA I N				E X I T
1. Select “7.1CH INPUT” in the SETUP MAIN
MENU with the			or cursor buttons, and
press the ENTER button.
2. To select “VIDEO IN”, press					or cursor
button.
3. Using the		or	cursor buttons, select the

video input source which is emitted from Monitor out in the 7.1 CH INPUT function. The input source is switched by pressing the

or cursor buttons as follows;

LAST ↔ TV ↔ DVD ↔ VCR1 ↔ DSS ↔ AUX1 ↔ V-OFF ↔ LAST ↔

Notes:

•When select LAST, the source is set previous source before 7.1 CH INPUT function is activated.

•When select V-OFF, no signal is emitted from monitor out terminal.

4.To Select desired channel , press the or cursor buttons.

5.	Using the or cursor buttons, adjust the
6.	volume level of each channel.
	After you complete this portion of the set up,

move the cursor to “MAIN” with the or cursor buttons and press the ENTER button.

Notes:

•These settings will be memorized to 7.1CH INPUT source.

•This feature can be directly selected with the CH.SEL button of the remote controller.

9 MULTI PLC SETUP

This submenu is for setting up the Multi PLC feature of the ZR6001.

9 MU L T I P L C

MU L T I P L C S E R V E R : ON

CONN E C T I ON MOD E :

AU T O
H I GH		AUD I O QUA L I T Y
H I GH		R E L I AB I L I T Y
GP	I D S E T T I NG : S T AR T
MA I N		E X I T

1. Select “9. MULTI PLC” in the SETUP MAIN

MENU with the or cursor buttons and press the ENTER button.

2. To select desired contents, press or cursor button.

MULTI PLC SEVER:

Select “ON” or “OFF” with the/cursor buttons to turn the Multi PLC Server feature ON/OFF.

CONNECTION MODE:

Select the Connection Mode of the Multi PLC feature with the/cursor buttons.

The available Connection Modes are:

- AUTO:Normal mode Use this mode as standard.

- HIGH AUDIO QUALITY(H-AQ)

:Emphasizes audio quality.

Use this mode to listen to high audio quality. (However, when multiple ZC4001 units are connected, audio may be lost or noise may occur in a ZC4001 that experience poor reception.)

- HIGH RELIABILITY(H-R)

:Emphasizes reliability.

Use this mode when multiple ZC4001 units are connected, audio is lost, or noise occurs.

GP-ID SETTING

To set a Group ID, connect the AC power cables of the ZR6001 and ZC4001 to wall power outlets as close to each other as possible.

Set the Group ID simultaneously for the ZR6001 and ZC4001.

<ZR6001>

Using the OSD menu system, set “GP - ID SETTING” to “START”.

ZR6001 ON SCREEN DISPLAY MENU SYSTEM

9 MU L T I P L C

MU L T I P L C S E R V E R : ON

CONN E C T I ON MOD E :

AU T O
H I GH		AUD I O QUA L I T Y
H I GH		R E L I AB I L I T Y
GP	I D S E T T I NG : S T AR T
MA I N		E X I T

1. Select “9. MULTI PLC” in the SETUP MAIN MENU with the or cursor buttons, and press the ENTER button.

2. Select “GP-ID SETTING” with the or cursor buttons.

<ZC4001>

1. 3. 2.

1. Press and hold the ENTER button for 5 sec or more.

24