Marantz ZR6001 AUX2 INPUT, Lip.Sync, Listening To The Tuner, Basic Operation, English, Notes

1. Select a desired Video source to decide the routed video signal to the Monitor Outputs .

2. Press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote to switch the 7.1 channel input.

3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the remote.

Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between –10 to +10 dB. The subwoofer can be adjusted between –15 and +10 dB.

These adjustments result will be stored to 7.1 CH. INPUT memory.

4. Adjust the main volume with the MAIN VOLUME knob or the VOL buttons on the remote.

To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote.

Notes:

• When the 7.1 CH. Input is in use, you may not

select a surround mode, as the external decoder

determines processing.

• In addition, there is no signal at the record outputs

AUX2 INPUT

If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder,

L(front left) and R (front right) inputs terminals are available as AUX2 input.

In this case, You can connect additional audio source to AUX2 as other audio input terminals.

SURROUND	PURE	SIMPLE
MODE	DIRECT	SETUP
AUTO	HT-EQ	MENU

LIP.SYNC

Depending on the image device (TV, monitor, projector, etc.) connected to the ZR6001, a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the ZR6001 to correct the time lag between the sound and image. It can be operated with the “LIP.SYNC” and and cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC

BASIC OPERATION

(TUNER)

LISTENING TO THE TUNER

Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country’s standard is 9 kHz step, Press TUNER button on the remote more than 6 seconds. Scan step will change.

Note:

•Preset memory for the tuner will clear by changing this setup.

•When using the PLC feature, AM sensitivity may decrease because of the effects of the PLC signals. There is nothing wrong with the equipment.

AUTO TUNING

		2.			1.		TV	VCR1	DSS/VCR2	DVD
						1.	TUNER	CD	TAPE	CDR/MD
								AUX1	AMP
							TV			MAIN
							VOL.	SLEEP	MUTE	VOL.
							CLEAR	MEMO	A/D	P.SCAN/V OFF
									0
									CHANNEL/SKIP
ND	PURE	SIMPLE
	DIRECT	SETUP	DISPLAY	MEMORY	CLEAR
		ENTER				2.	BASS	TREBLE	TUNE/SEARCH
	HT-EQ	MENU	EXIT	BAND	T-MODE
								T-MODE	RDS	F.DIRECT

INPUT/DISC+ AUDIO SUB-T/ATT PTY

MANUAL TUNING

		2.			1.		TV	VCR1	DSS/VCR2	DVD
						1.	TUNER	CD	TAPE	CDR/MD
								AUX1	AMP
							TV			MAIN
							VOL.	SLEEP	MUTE	VOL.
							CLEAR	MEMO	A/D	P.SCAN/V OFF
									0
ND	PURE	SIMPLE							CHANNEL/SKIP
	DIRECT	SETUP	DISPLAY	MEMORY	CLEAR
			ENTER			2.
	HT-EQ	MENU	EXIT	BAND	T-MODE		BASS	TREBLE	TUNE/SEARCH
								T-MODE	RDS	F.DIRECT

INPUT/DISC+ AUDIO SUB-T/ATT PTY

(Using the ZR6001)

1. To select tuner and desired band (FM or AM), press the BAND button on the front panel

2. Press the or cursor buttons on the front panel to select the desired station.

(Using the remote control unit)

1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote.

2. Press the 5 or 6 on the remote to tune in the desired station.

DIRECT FREQUENCY CALL

		PURE DIRECT	AUTO		DTS
	3.		1	2	3
		NIGHT	CSII	EX/ES	VIRTUAL
POWER			4	5	6
		DISPLAY	MCH-ST	STEREO	7.1CH IN
			7	8	9

ENGLISH

when the 7.1 CH. Input is in use.

feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.

Note:

• The LIP.SYSNC feature turns OFF (0 ms) in the

(Using the ZR6001)

1. To select tuner and desired band (FM or AM), press the BAND button on the front panel.

2. Press the or cursor buttons on the front panel for more than 1 second to start the auto tuning function.

	TV	VCR1	DSS/VCR2	DVD
1.	TUNER	CD	TAPE	CDR/MD
		AUX1	AMP
	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.
	OSD		MENU

CLEAR MEMO A/D P.SCAN/V-OFF

0

CHANNEL/SKIP

BASS TREBLE TUNE/SEARCH

2.		T-MODE	RDS	F.DIRECT
	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY

CH.SEL LIP.SYNC

SYSTEM REMOTE CONTROLLER

PURE DIRECT mode. When the PURE DIRECT

mode is deactivated, the set value of the

LIP.SYSNC feature is automatically restored.

3. Automatic searching begins then stops when a station is tuned in.

(Using the remote control unit)

1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote.

2. Press the 5 or 6 for more than 1 second on the remote.

3. Automatic searching begins then stops when a station is tuned in.

If tuning does not stop at the desired station, use to the “Manual tuning” operation.

1. To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote.

2. Press the F.DIRECT on the remote, display will show “FREQ - - - -”.

3. Input your desired station’s frequency with the numeric buttons on the remote.

4. The desired station will automatically be tuned.

33