Marantz ZR6001 manual Unit, Operation Of Remote Control, Notes

ENGLISH	OPERATION OF REMOTE CONTROL
	UNIT
	REMOTE CONTROL

3. Close the cover until it clicks.

GENERAL INFORMATION OF RC5500SR TO ZR6001

To control the ZR6001 by your RC5500SR, you have to select the device AMP or TUNER by pressing the function selector button. Please refer below for the details in AMP and TUNER mode.

The distance between the transmitter of the

remote control and the IR SENSOR of the ZR6001

should be less than 5 meters. If the remote control

is pointed in a direction other than the IR SENSOR

or if there is an obstacle between them, use of the

remote control may not be possible.

Remote-controllable range

ZR6001

60°

Remote control unit (RC5500SR)

LOADING BATTERIES

The life of the batteries used with the remote control is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak.

1. Remove the back cover.

Notes:

•Do not mix alkaline and manganese batteries.

•Do not mix old and new batteries.

CAUTIONS ON BATTERIES

•	Use “AAA” type batteries in this remote control
	unit.
•	If the remote control unit does not operate from
	close to the main unit, replace the batteries with
	new ones, even if less then a year has passed.
• The included battery is only for verifying
	operation. Replace it with a new battery as soon
	as possible.
•	When inserting the batteries, be careful to do so
	in the proper direction, following the + and -
	marks in the remote control unit’s battery
	compartment.
•	To prevent damage or battery fluid leakage:
	-	Do not use a new battery with an old one.
	-	Do not use two different types of batteries.
	- Do not short-circuit, disassemble, heat or
		dispose of batteries in flames.
• Remove the batteries when not planning to use

AMP MODE

POWER

TV	VCR1	DSS/VCR2	DVD
TUNER	CD	TAPE	CDR/MD
	AUX1	AMP
TV			MAIN
VOL.	SLEEP	MUTE	VOL.
OSD		MENU
	ENTER
SET UP/		MENU OFF
T.TONE
PURE DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN
	7	8	9
CLEAR	MEMO	A/D	P.SCAN/V-OFF
		0
		CHANNEL/SKIP
BASS	TREBLE	TUNE/SEARCH
	T-MODE	RDS	F.DIRECT

INPUT/DISC+ AUDIO SUB-T/ATT PTY

CH.SEL LIP.SYNC

SYSTEM REMOTE CONTROLLER

RC5500SR

TUNER MODE

POWER	Turns the ZR6001 on and off
Function selector *	Selects a particular source component
SLEEP *	Sets the sleep timer function
MUTE *	Decreases the sound temporarily
VOL 34 *	Adjusts the over all sound level
MENU	Enters the SETUP MENU
Cursor	Moves the cursor for settings in the SETUP MENU
ENTER	• Enters the SETUP MENU
	• Confirms the settings in SETUP MENU
SETUP/T.TONE	Enters the test tone mode for setting the Speaker Level Setup
MENU OFF	Exits from the SETUP MENU
PURE DIRECT *	Selects the Pure Direct mode
NIGHT *	Turns on or off the NIGHT mode
DISPLAY *	Change the front display mode
Surround mode (1-8)	Selects the surround mode
7.1CH-IN (9)	Selects the 7.1CH IN
A/D (0)	Switches between the analog and digital inputs
BASS 34 *	Adjusts the tone control of low frequency sound
TREBLE 34 *	Adjusts the tone control of high frequency sound
SUB-T/ATT	Reduces the input level
P.SCAN/V-OFF	Turns on or off the Video output
CH. SEL	Adjusts the input level
LIP.SYNC	Selects the LIP. SYNC mode

2. Insert the new batteries (AAA type) with

correct and polarity.

the remote control unit for a long period of time.

• If the batteries should leak, carefully wipe off the

fluid from the inside of the battery compartment,

then insert new batteries.

• When disposing of used batteries, please

comply with governmental regulations or

environmental public instruction’s rules that

apply in your country or area.

POWER

TV	VCR1	DSS/VCR2	DVD
TUNER	CD	TAPE	CDR/MD
	AUX1	AMP
TV			MAIN
VOL.	SLEEP	MUTE	VOL.
OSD		MENU
	ENTER
SET UP/		MENU OFF
T.TONE
PURE DIRECT	AUTO		DTS
	1	2	3
NIGHT	CSII	EX/ES	VIRTUAL
	4	5	6
DISPLAY	MCH-ST	STEREO	7.1CH IN
	7	8	9
CLEAR	MEMO	A/D	P.SCAN/V-OFF
		0
		CHANNEL/SKIP
BASS	TREBLE	TUNE/SEARCH
	T-MODE	RDS	F.DIRECT

INPUT/DISC+ AUDIO SUB-T/ATT PTY

CH.SEL LIP.SYNC

SYSTEM REMOTE CONTROLLER

RC5500SR

* These buttons are used to control ZR6001 in any function mode.

TUNER	Selects a frequency band
0-9	Inputs the numeric #s
CLEAR	Clears the inputting
MEMO	Enters the tuner preset memory numbers
P.SCAN/V-OFF	Starts preset scan
CHANNEL/SKIP	• Selects a preset station
4 / ¢
TUNE/SEARCH	Tunes a station
5 / 6
T-MODE 1 2	Selects the auto stereo mode or mono mode
F.DIRECT 2	Selects the “Frequency direct input”

10