2. Press the 
button once.
3. Simultaneously press the ENTER buttons of the ZR6001 and ZC4001.
<ZC4001>
<ZR6001>
GP-ID SETTING : ＊＊
The below message appears when the Group ID has been successfully set.
<ZC4001>
<ZR6001>
The below message appears if the units fail to set the Group ID.
<ZC4001>
<ZR6001>
Notes:
One possible reason the Group ID cannot be set is power line noise. In that case, unplug the power cable of the device that is generating noise, then plug it back in and try setting the Group ID again.
PLC IR EMITTER OUT SETUP
When the ZR6001 and ZC4001 are connected over the PLC, the ZC4001 can control output from other brands.
The ZR6001’s IR EMITTER OUT terminals output remote control signals from the ZC4001 to an emitter, which are then picked up by the IR sensor of other brand products. To control other brand sources, an IR code must be set. If the IR code of the source is unknown, the IR code learning feature must be used.
IR CODE SETTING
1. Press and hold the MENU button for 5 sec. or more.
2. “SET REMOTE IR” appears, followed by “INPUT IR CODE”.
3. Press the ENTER button.
4. Select a function to be controlled by ZR6001 with the
/
buttons.
(Select from DVD, TV, VCR1, DSS, AUX1, TAPE,
“FUNCTION : DVD”
5. Press the ENTER button.
6. Select a source device of the other brand with
the 
/ 
buttons. (See the PLC REMOTE CODES table at the end of this guide.
Select from TV, CABLE, V.ACC, DSS, VCR, LD, DVD, TUNER, AMP, CD, HOME, TAPE,
“DEVICE : DVD”
7. | Press the ENTER button. |
8. | Input the code of the source with the / |
buttons. Move to other digits in the code with the
/
buttons.
“CODE NR : 6000”
9. After inputting the code, press the ENTER button.
“WRONG NUMBER” appears if an incorrect code is input. In that case, press the ENTER button.
“CHECK IR CODE” appears followed by “CODE: POWER” if the correct code is input.
10. Press the ENTER button to output the Power Code from the IR EMITTER OUT terminal and subsequently via the emitter as a test.
IR CODE LEARNING
1. Press and hold the MENU button for 5 sec. or more.
2. | “SET REMOTE IR” appears, followed by | |
| “INPUT IR CODE”. | |
3. | Select “LEARN IR CODE” with the / | |
| buttons. |
|
4. | Press the ENTER button. | |
5. | Select a function to be controlled by ZR6001 | |
| with the | / buttons. |
| (Select from DVD, TV, VCR1, DSS, AUX1, | |
| TAPE, | |
| “FUNCTION : DVD” | |
6. | Press the ENTER button. | |
7. | Select a source device of the other brand with | |
| the / | buttons. |
| (Select from TV, CABLE, V.ACC, DSS, VCR, | |
| LD, DVD, TUNER, AMP, CD, HOME, TAPE, | |
| ||
| “DEVICE : DVD” | |
8. | Press the ENTER button. | |
9. | Select a button to learn with the / buttons. | |
| (Select from 0, | |
| ENTER, INPUT, PLAY, STOP, SEARCH+, | |
| SEARCH- and PAUSE.) | |
| “KEY : POWER” | |
10. | Press the ENTER button. | |
11. Face the remote controller of the other brand | ENGLISH | |
source towards the learning IR sensor on the | ||
| ||
front panel of the ZR6001 and press the |
| |
remote controller button to provide the code. |
| |
(In this case, the Power button is pressed.) |
| |
ZR6001 |
| |
Remote |
| |
controller of other |
| |
brand source |
| |
M |
| |
OK |
| |
Ex |
| |
S |
|
Remote controller | ZR6001 |
of other brand source
12. “LEARNING*” appears.
“FAIL LEARNING” appears if the ZR6001 fails to learn the IR code.
“ SUCCEED ” a p p e a r s i f t h e Z R 6 0 0 1 successfully learns the IR code. After that, “CHECK IR CODE” appears, followed by “CODE: POWER”.
13.Press the ENTER button to output the Power Code from the IR EMITTER OUT terminal and subsequently via the emitter as a test.
14.Press the EXIT button and repeat the procedure to learn the IR code for another remote controller button.
25
