Marantz ZR6001 Advanced Connecting, CONNECTING TO THE RC-5MARANTZ PRODUCTS ONLY, English, Front

ADVANCED CONNECTING

CONNECTING TO THE RC-5 (MARANTZ PRODUCTS ONLY)			ENGLISH
Y CB/PB	CR/PRY CB/PB CR/PR	Y CB/PB CR/PR
ANTENNA	COMPONENT VIDEO
INPUT-1	INPUT-2	MONITOR OUT

FM (75Ω) GND AM

VIDEO

S-VIDEO
VCR1	DSS/VCR2	MONITOR

DVD AUDIO PLAYER

or

SACD MULTI CHANNEL

PLAYER

			R L		R L	R L
						R L	R L	R L
COMPONENT VIDEO
INPUT-1		INPUT-2			MONITOR OUT
CB/PB CR/PR	Y	CB/PB	CR/PR	Y	CB/PB	CR/PR		CENTER
S-VIDEO		VCR1		DSS/VCR2		L
OR	DVD					MONITOR
TV		IN	OUT	IN	OUT	OUT

R

TV	DVD	VCR1	DSS/VCR2		MONITOR
	IN	OUT	IN	OUT	OUT
	DIGITAL IN	DIGITAL OUT
3	4	COAX.

RS-232C

1	2	OPT.
TV	DVD	VCR1	DSS/VCR2		CD
L
R
	IN	OUT	IN	OUT

TV DVD IN OUT IN OUT OUT

RC-5	MULTI		L	SL	SBL	C		2
	RC							MODEL
	IN
		FLASHER					PRE
		IN						RC OUT
							OUT
	OUT		R	SR	SBR	SW		OPTION
TAPE	CDR/MD	MULTI	L	SL	SBL	C
							7.1CH
							IN
IN OUT	IN OUT	OUT	R	SR	SBR	SW

CENTER

L

R

FRONT SURR. SURR. SUB

BACK WOOFER

RC	L	SL	SBL	C	FRONT	SURR.	SURR.	SUB
							BACK	WOOFER
MULTI
RC-5
	IN				MODEL

2C		FLASHER				PRE	POWER
		IN
						OUT
	OUT		R	SR	SBR	SW	AMPLIFER
TAPE	CDR/MD	MULTI	L	SL	SBL	C
						7.1CH	Subwoofer
						IN
IN OUT	IN OUT	OUT	R	SR	SBR	SW
AUDIO			(AUX2)

AUDIO(AUX2)

1

REMOTE	CD RECORDER	REMOTE	MD DECK	REMOTE	CD PLAYER
CONTROL		CONTROL		CONTROL

R L R L R L

L R L R L R

Front	Center	Front
Left		Right
Surround	Surround
Left		Right
Surround		Surround
Back Left		Back Right

IN	IN	IN
OUT	OUT	OUT
EXTERNAL INTERNAL	EXTERNAL INTERNAL	EXTERNAL INTERNAL

q

w

CONNECTING MULTI CHANNEL AUDIO SOURCE

The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder.

If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 32.

CONNECTING AN EXTERNAL POWER AMPLIFIER

The PREOUT jacks are for connecting external power amplifiers.

Be sure to connect each speaker to the corresponding external power amplifier.

You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit.

The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier’s, power switch is synchronized with this unit’s power switch.

Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature.

Whenever external infrared sensors or similar devices are connected to RC-5 IN of the ZR6001, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure.

1. Hold down the MULTI button and MENU button on the front panel at the same time for five seconds.

2. The setting “IR=ENABLE” is shown on the FL DISPLAY.

3. Press theorcursor button to change this to “IR=DISABLE”.

4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled.

Note:

•Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands.

5.To restore the original setting, perform steps 1 to 4 to set to “IR=ENABLE”.

17