M e s s a g e s
Display readout | Appears if... |
| What to do |
|
|
|
|
AUTO (Automatic protocol | ... automatic protocol detection is enabled | • | Verify that the controller is sending |
detection error) | but the protocol (Martin/DMX) cannot be |
| and the serial link is properly con- |
| determined because there is no control |
| nected. |
| data. |
|
|
|
|
|
|
LERR (Lamp error) | ... the lamp doesn’t ignite within 10 min- | • | Check the lamp |
| utes of receiving the ‘Lamp ON’ com- | • | Check that the voltage and fre- |
| mand. Likely reasons are a missing or |
| quency settings match the local |
| defective lamp, or insufficient AC voltage. |
| supply. |
|
|
|
|
MERR (Memory error) | ...the EEPROM memory cannot be read. | • | Contact Martin service personnel |
|
|
| for assistance. |
|
|
|
|
CSER | ...a software upload is unsuccessful. | • | Reload software, see page 23. |
|
|
|
|
**** | ... there is no communication between the | • | Check fuses and replace accord- |
| control panel and motherboard. This |
| ingly. |
| readout appears briefly when switching | • | Check that cable between control |
| on the fixture. |
| panel and motherboard is con- |
|
|
| nected properly. |
|
| • | Reinstall software. |
|
|
|
|
ShER (Short error) | ... the fixture detects the lamp is ON but | • | Contact Martin service personnel |
| no ‘Lamp ON’ command has been |
| for assistance. |
| received. This can occur if the lamp relay |
|
|
| is stuck or if the |
|
|
| cuit fails. The fixture may be operated but |
|
|
| remote lamp on/off may be effected. |
|
|
|
|
|
|
Hot (Hot lamp) | ... you attempt to strike the lamp within 8 | • | Wait until the lamp strikes. |
| minutes after having switched it off. The |
|
|
| fixture will store the ‘Lamp ON’ instruction |
|
|
| and strike the lamp once the 8 minutes |
|
|
| period has elapsed. |
|
|
|
|
|
|
bTER (Base temperature error) | ...there is a malfunction in the base or | • | Contact Martin service personnel |
HTER (Head temperature | head temperature sensing circuit. |
| for assistance. |
error) |
|
|
|
|
|
|
|
FbEP (Feedback error pan) | ...pan (FbEp), tilt (FbET) or both (FbER) | • | Contact Martin service personnel |
FbET (Feedback error tilt) | feedback circuits are malfunctioning. It |
| for assistance. |
FbER (Feedback error pan/tilt) | will still be possible to operate the fixture, |
|
|
though it goes into a “safe” mode where |
|
| |
|
|
| |
| maximum speed is reduced, thus prevent- |
|
|
| ing the fixture from losing track of its |
|
|
| home position (losing step). |
|
|
|
|
|
|
PAER (Pan | ...the pan or tilt indexing circuit is malfunc- | • | Contact Martin service personnel |
TIER (Tilt | tioning. The fixture will, after the |
| for assistance. |
| establish a mechanical stop, and continue |
|
|
| to work normally. |
|
|
|
|
|
|
C1ER (Color wheel 1 | ...the | • | Contact Martin service personnel |
C2ER (Color wheel 2 | tions (e.g. sensor defective or magnet |
| for assistance. |
FgER (Fixed gobo | missing). After the |
|
|
question stops in a random position. |
|
| |
RgER (Rot. gobo |
|
| |
|
|
| |
|
|
|
|
Appendices | 31 |
