6.TROUBLESHOOTING AIDS
6.1.ERROR HANDLING
The timer allows the full control of the washing machine. When an error occurs then automatically the machine will go over to a safe state. With the diagnostic program you can determine the problem (See „Programming manual"). This program will test all the functions of the washing machine.
If a failure occurs then the computer will display a diagnostic message. The message is a number that correspond with a typical problem.
If a failure occurs and the timer gives no message you can consult chapter 6.2.
6.2. PROBLEM CHECK LIST
Problem | Cause | Solving the problem | |
When the power is switched on : | • no external power | • verify the external tension of the | |
the display is not lighting up |
| machine | |
| • the emergency button is activated | • deactivate the emergency button | |
Remark : | • the power connector is not | • connect the power connector | |
The display must always light up | connected on the board |
| |
when the power connector is | • the power connector is inverse | • check the wiring and connect the | |
connected to the power board | connected | connector as it must be | |
(EPROM with software must be | • the fuse on the PWR board has | • if the transformer is deformed replace | |
implemented) | |||
jumped | the PWR board | ||
| |||
|
| Check the wiring and the tension at the | |
|
| power Connector | |
|
| If the transformer is still OK change the | |
|
| Fuse | |
| • the input connector is disconnected | • if the display is lighting up: verify that | |
| the input signals or the + 16 V signal are | ||
|
| ||
|
| not touching the cabinet | |
| • the EPROM that contains the | • put the right EPROM with software into | |
| software is not implemented | the socket on the board. | |
|
|
| |
The machine is not starting up when | • the key switch stands in Program | • set the Key switch to Run mode | |
the start button is pressed. | mode |
| |
| • the correct amount of coins is not | • the start button must be pressed when | |
| inserted | ||
| 00 is flashing on the lower display | ||
| • the door is not closed properly | ||
| • close the door | ||
|
| ||
|
|
| |
Coins are inserted but the displayed | • the micro contact mounted on the | • verify the well functioning of the micro | |
program price is not counting down | coin drop is not functional | contact of the coindrop : | |
|
| positive pulses should be generated | |
| • the optocoupler mounted on the | • verify the well functioning of the | |
| coindrop is not functional | optocoupler positive pulses should be | |
|
| generated | |
| • check the wiring to the coindrop | • if the wiring is broken: repair the wiring | |
| • insert the correct coin value in the u- | ||
| • verify if you have entered a coin | ||
| submenu | ||
| value in the | ||
|
| ||
| corresponding coindrop |
| |
|
|
| |
Coindrop is accepting coins but does | • the start button is not pushed after | • push the start button | |
not start the washer | the amount is flashing on ‘00’ |
| |
| • the right amount is not reached | •Put the right amount in the coindrop | |
| • the door is not closed properly | ||
| • close the door | ||
|
| ||
|
|
| |
The machine is not responding on | • the key switch is not functional (no | • check if the input connector A is well | |
pressing the keyboard buttons | dot is displayed when switching in | connected and check the wiring between | |
| Program mode) | the input connector and the keyswitch | |
| • the START button is not functional | • set the Key switch to Run mode | |
| (the key switch stands in Program |
| |
| mode) | • set the Key switch to Program mode | |
| • the SET button is not functional (the | ||
|
| ||
| key switch stands in Run mode) | • check if the connector K of the keyboard | |
| • no button is functional and the key | ||
| is well connected | ||
| switch is in the right position | ||
|
| ||
|
|
| |
The dot to indicate that the software is | • the key switch is not functional | • check if the input connector A is well | |
in program mode can not be enabled |
| connected and check the wiring between | |
or disabled | • the infrared key is not functional | the input connector and the keyswitch | |
| • set the | ||
|
|
24 | INSTALLATION AND MAINTENANCE MANUAL | PUBLICATION DATE Sep 05 100646 |