Manuals / Meridian Audio / Home Audio / Home Theater System

Meridian Audio 8000 Adjusting the volume, Muted, Radio, To change the volume, To mute the sound

Models: 8000

1 45

Download 45 pages 44.86 Kb

Page 27

Image 27

USING THE DSP8000

LOUDSPEAKERS

Adjusting the volume

The DSP8000 loudspeakers adjust the volume in precise steps of 1dB, where 9dB is equivalent to doubling the loudness, and can be varied in the range 1 to 99dB.

When you first connect power to the DSP8000 loudspeakers the volume is set to 65, which is similar to the midway position of the rotary volume control on a conventional preamplifier.

To change the volume

• Press the red A or V keys on the remote.

As you adjust the volume setting the display	Radio 55
will show the current volume level:	Radio 55
To mute the sound
• Press Mute on the remote.
The display will show:	Muted
To restore the sound
• Press Mute again on the remote.

Alternatively, the sound will be restored if you adjust the volume.

Page 27

Image 27

Meridian Audio 8000 Adjusting the volume, Muted, Radio, To change the volume, To mute the sound, To restore the sound

Contents

8 0 M E R I D I A N D S P L O U D S P E A K E RU S E R G U I D E Volume Meridian DSP8000 Digital LoudspeakerSystem User Guide PhaseDesigned and manufactured in the UK by Copyright and acknowledgementsSales and service in the UK Sales and service in the USAContents Index Introduction Meridian DSP8000 loudspeaker system Digital Signal ProcessingDSP loudspeaker drivers Power amplifiers Meridian High Resolution MHRCabinet Meridian Comms Sample configurations Meridian Digital TheatreMeridian Digital Music System Digital inputs and outputs SpecificationSignal processing CharacteristicsFinished in high-glossblack piano lacquer PowerCabinet Glass frontAvailable accessories Setting up the DSP8000 loudspeakers Unpacking UnpackingCare when unpacking ComponentsTo dismantle the loudspeakers Tightening the drive unitsRadio interference To obtain the best sound Positioning the DSP8000 loudspeakersSafety warnings To avoid overheatingCommunications connections Connecting the loudspeakersBack panel Digital connectionsTo use a DSP loudspeaker as a centre speaker Connecting to other equipmentDSP loudspeakers S5 lead 508.24 24-BitCD PlayerDSP loudspeaker - Main R M5 lead DSP loudspeaker - Main LDSP8000 LOUDSPEAKERS SETTING UP THEUsing the DSP8000 loudspeakers To select a source Selecting a sourceRadio To switch to standbyRadio Changing the displayPCM 96k Status indicatorsTo restore the sound Adjusting the volumeMuted To change the volumeBass+0.0 Changing the tilt, bass or phasePhase + Tilt+0.0Bal ResetChanging the listening position BalConfiguring the DSP8000 loudspeakers Choosing standard settings Type LTo select a standard setting L. Slv To specify the speaker positionTo choose master or slave Specifying information about your system L 500 Auto S.A. P.A. L.E. Bal. Y Centre N Diag. NTo configure the DSP8000 loudspeaker Configuring the sources RD RadioTo configure a source Initial value Radio D1 2C1A FF. Y OptionTo select Setup mode Configuring the setup optionsSetup C.Tilt+1To store the settings StoreTroubleshooting Remote not working TroubleshootingUnit goes silent when played hard Display on front panel not litSound is odd or mono The yellow indicator flashes or stays onUnit stays in standby Only the master loudspeaker playsMaintenance and cleaning CleaningFitting and removing the grilles Service and guarantee ServiceGuarantee TROUBLESHOOTING Index