Meridian Audio FDP-DILA3 Controls and Features, Remote Control’s signal transmitter, EXIT button

Controls and Features

1Remote Control’s signal transmitter

(☞ page 17)

2OPERATE button

When the projector is in the standby mode, pressing this button for one second or more will turn on the projector and light up the OPERATE indicator. Press it one second or

more again and the projector will turn off, cool down and finally enter the standby mode.(☞ page 24)

*The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Use the button after approximately 1 minute.

3SCREEN button

Each time you press this button, the selection alternates

between wide screen size (16:9) and standard screen size (4:3). (☞ page 30)

4DIGITAL ZOOM ª / · buttons

This digital zoom function can magnify the image up to four times on the screen. (☞ page 27)

*There will however be some inevitable loss of image qual- ity when images are enlarged.

5FREEZE button

This button allows the image to be retained in the projector memory and stills the picture on the screen. Press the but-

ton once to freeze the picture and again to de-freeze. (☞ page 28)

6QUICK ALIGN. (quick alignment) button

Use this button to automatically adjust the projected im- age’s (i)horizontal and vertical position, (ii) Width and dis- play area, etc. During alignment, the message “QUICK

ALIGN.” appears on the screen and disappears when align- ment is complete. (☞ page 30)

*The ‘Quick Alignment’ function only works when the sig- nal is input from either the PC 1 or PC 2 terminal. It does not work when the signal is input from the VIDEO IN ter- minal or the Y/C input terminal.

7EXIT button

Press this button to display the previous hierarchical menu (For example, from sub-menu to main menu). When the

main menu is displayed, pressing this button will cause the menu to disappear. (☞ page 34)

8ENTER button

Press this button to show the next hierarchical menu (For example, from main menu to sub menu). It is also used

when “ENTER” is displayed against the item on the menu screen or to select the “Reset” menu. (☞ page 34)

9HIDE button

Use this button to turn off the image on the screen and

audio sound temporarily. Pressing it again causes the im- age and audio sound to resume. (☞ page 28)

pCURSOR ( /  /  /  ) buttons

These buttons are used in the menu mode to select an item, adjust the value etc. (☞ page 34)

qVIDEO button

Use this button to select a device such as a video con-

nected to the VIDEO IN terminal (VIDEO or Y/C Input ter- minal) of the projector. (☞ page 24)

wPC button

Use this button to select a device connected to the PC 1, PC 2 or PC 3 terminal. (☞ page 25)

eH-KEYSTONE button

Use this button to remove the horizontal trapezoidal distor- tion of the image projected on the screen. (☞ page 29)

rV-KEYSTONE button

Use this button to remove the vertical trapezoidal distortion of the image projected on the screen. (☞ page 29)

tVOLUME ª / · button

Use these buttons to adjust the sound volume. (☞ page 28)

yFOCUS button*

Not Active

uMENU button

Use this button to enter or exit the menu mode. When the

main menu is displayed, press this button and it will disap- pear. (☞ page 34)

iPRESET button

This PRESET button only works as a reset button for the [VOLUME], [V-KEYSTONE] and [H-KEYSTONE] adjust- ments done on the control panel and the [VOLUME], [DIGITAL ZOOM] and [SCREEN „] adjustments done on the remote control. (☞ page 27, 29)

When adjusting the volume, keystone or digital zoom (when the setting is displayed on the screen) the adjusted value is reset to that which was set when the projector was shipped

from the factory. This button does not work for the menu (submenu) items. (☞ page 34)

12