Meridian Audio FDP-DILA3 warranty Connector Panel, Controls and Features

Controls and Features

Connector Panel

1 PC2 Input Terminal	2 PC1 Input Terminal		3 PC3 Input Terminal
			Connect Processor
			Here
R PR/CR G Y B PB/CS	H/CS	V	DVI

Remove cover to access

				PC1		PC3
		PC2
DC OUT		REMOTE	RS-232C OUT	RS-232C IN	Y/C	VIDEO
5V }1.5A	AUDIO IN		CONTROL		VIDEO IN

4 DC OUT	6 REMOTE	8 Y/C Input
Terminal	Terminal	Terminal
5 AUDIO Input Terminal		7 CONTROL RS232C	9 VIDEO Input
		IN/OUT Terminal	Terminal

1PC 2 Input terminal [BNC x 5]

These are multipurpose video input terminals that allow in- put of the following signals: analog RGB signals, vertical sync (V) signals, and horizontal sync (H) signals /compos- ite signals (Cs). Devices which have analog RGB signal output terminals can be connected. This terminal can also be used as an input terminal for component signals (Y,CB,CR) or DTV-format (Y, PB,PR) signals. Devices which have component signals output terminals can be connected. (☞ page 22)

To use this terminal, the “PC2 (BNC)” item in the “Options” menu must be set correctly according to the input signals. (☞ page 39)

*Input of external sync signals is automatically detected. Detection of H/V signals or Cs signals causes automatic switching to external sync. The priority order is H/V>Cs.

*When computer-related signals are input, the uppermost edge of the image may appear to bow if the sync signal input is composite sync (Cs) or G on sync signal. In this case, please use separate sync signals for vertical sync

(V) and horizontal sync (H).

2PC 1 input terminal (D-sub 3 rows 15 pin)

This is an input terminal dedicated to computer signals (RGB Video signals and sync signals).

Connect the display output terminal of the computer to this terminal. When a Macintosh computer is to be connected, please use the conversion adapter (sold separately) for Mac. (☞ page 22)

*When computer signals are input, the uppermost edge of the image may appear to bow if the sync signal input is composite sync signals or G on sync signals.

3PC 3 input terminal [DVI-D (Dual/ Single) 24 Pin]

This is an input terminal dedicated to computer signals

(DVI-D Terminal Dual/ Single). Connect the display output terminal of the processor to this terminal.

4DC OUT Terminal

This is the DC 5V, 1.5A power source output terminal.

Please do not use optional devices other than those specified.

5AUDIO (audio) input terminal [mini jack]

This is the audio input terminal for devices connected to PC1, PC2, PC3, Video or Y/C. Connect the audio output terminal of the device to this terminal. (☞ page 21, 22)

*When PC 1, PC 2, PC3, Video or Y/C input is being se- lected, the inputted audio signals will be reproduced by the projector speaker.

(Audio output for this projector is monoaural.)

6REMOTE terminal (stereo mini jack)

When the remote control is unable to work due to rear pro- jection etc., the REMOTE terminal can be used to connect an external sensor to the projector. The external sensor is not sold. Please check with your authorized dealer.

7CONTROL RS232C IN/OUT Terminal [D-sub 9 Pin]

This is the RS-232C interface-specific terminal. The pro- jector can be controlled by a computer connected exter-

nally. More than one computers can be controlled using both the RS-232C IN and OUT terminals. (☞ page 22)

*For details, please check with your dealer.

8Y/C Input Terminal [Mini DIN 4 PIN]

This is the input terminal for Y/C (S-Video) signals. Con- nect these sources to the S-video terminal of the video processor.

9VIDEO Input Terminal [RCA pin jack]

This is an input terminal for composite video signals. Con- nect these sources to the Video terminal of the video processor.

8